

Worn down to metal
- Cause
- Grinding during braking, squealing when pressing the pedal
- Found
- Pads worn down to the metal backing, disc with grooves
- Done
- Replaced pads, resurfaced discs, lubricated guide pins

Mercedes brake pad replacement is a basic procedure that ensures braking safety and efficiency. At our auto service in Almaty, you can replace pads on any Mercedes model: from A-Class to G-Class. We use original parts and quality aftermarket equivalents, and provide a 6-month warranty on labor and parts. The average replacement price is 4,500 tenge per axle; the exact cost depends on the model and complexity of the work.
Mercedes brake system work: pads, discs, calipers, fluid

We remove the old pads, clean and lubricate the seating surfaces, and install new ones. We check disc wear and caliper operation.

We replace the rear axle pads, service the brackets and guide pins. After installation, we check the travel and even contact.

We install pads with a wear sensor and connect its connector. We check that the indicator on the dashboard goes out correctly.

We remove the old discs, clean carbon deposits from the hub, and install new ones. We measure runout and thickness to eliminate vibration during braking.

We replace the rear axle brake discs and clean the seating surfaces. We check the condition of the pads and parking brake.

We drain the old fluid and bleed the circuits under pressure to remove air. We top up with new fluid and check the level and pedal.

We remove the caliper, disassemble and inspect the piston and boots, lubricate and reassemble. We restore normal travel and even braking.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
We show six real examples — what it was and what it became after replacement.
Cost depends on the model and drive type. Confirm the exact price by phone or WhatsApp.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Front Pad Replacement (A, B, C-Class) | 1 hour | 6 mo | from 5 500 ₸ |
| Front Pad Replacement (E, S, M-Class) | 1–1.5 hours | 6 mo | from 6 500 ₸ |
| Rear Pad Replacement (A, B, C-Class) | 1 hour | 6 mo | from 4 500 ₸ |
| Rear Pad Replacement (E, S, M-Class) | 1–1.5 hours | 6 mo | from 5 500 ₸ |
| Pad Replacement with Electronic Parking Brake | 1.5–2 hours | 6 mo | from 8 000 ₸ |
| Pad Replacement with Wear Sensor | 1.5 hours | 6 mo | from 7 000 ₸ |
| Front Brake Disc Replacement | 1–1.5 hours | 6 mo | from 7 000 ₸ |
| Rear Brake Disc Replacement | 1 hour | 6 mo | from 6 500 ₸ |
| Brake Fluid Replacement | 1 hour | 6 mo | from 3 000 ₸ |
| Caliper Repair (removal, inspection, lubrication) | 2–3 hours | 6 mo | from 10 000 ₸ |
| Caliper Guide Replacement | 1–2 hours | 6 mo | from 5 000 ₸ |
| Brake System Diagnostics | 30 min | 6 mo | from 2 000 ₸ |
| ABS/ESP Computer Diagnostics | 1 hour | 6 mo | from 5 000 ₸ |
| Brake Pad Wear Sensor Replacement | 30 min | 6 mo | from 3 000 ₸ |
| Cleaning and Lubrication of Brake Mechanisms | 1–2 hours | 6 mo | from 4 000 ₸ |
Prices are for labor only and do not include the cost of parts. A discount is available for comprehensive brake system repair. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
We apply high-temperature paste to the guides, piston, and pad ends. Without it, pads squeak and seize after a couple thousand km.
We install pads with a sensor specific to the Mercedes model, without resoldering the connector. Otherwise, a brake error appears on the dashboard.
We replace the fluid with a full pressure bleed, not just a top-up. Old fluid with water boils during braking — the pedal sinks.
We are responsible for assembly, lubrication, and bleeding. If it squeaks or warps, you come back, and we redo it for free.
We show the process from request to vehicle handover — transparently and step by step.

You submit a request on the website or by phone, and we find a convenient time for your visit. On the lift, we check the condition of the pads, discs, calipers, and brake hoses.
request on WhatsApp
We quote the final cost after diagnostics — including labor and original parts.
inspection and diagnosticsWe use original Mercedes pads or proven equivalents with a quality guarantee.
estimate before work starts
We carefully remove the wheels and gain access to the brake mechanisms.
work to factory procedureWe remove the worn pads, clean the caliper, and install new ones with guide lubrication.
result check
We install the wheels, bleed the brakes if necessary, and check the pedal operation. We conduct a test drive, provide a warranty on the work, and issue closing documents.
warranty in the work orderWalk-ins welcome. By appointment — no queue.
CARGID car repair team. 8–17 years of experience.
Author
Mobile auto electrician

Car alarm and car stereo installer

Auto electrician

Roadside assistance technician

Diagnostic technician

Engine mechanic (cylinder head repair)

Auto electrician and diagnostician

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

CARGID replaces Mercedes brake pads in Almaty with diagnostics and a written estimate before any work starts. We install pads with a wear sensor matched to your specific model, reset the electronic parking brake service mode with a dealer scanner, and lubricate 4 caliper points. A 6-month warranty is written into the work order.
Friction linings wear down gradually, and on a Mercedes several signals at once point to an upcoming replacement — from squealing to pedal feel. Here's what to watch for before you visit a shop.
If you drive on worn linings until the metal, the disc wears faster than normal and instead of a wear item you end up replacing the discs along with the caliper. The friction layer on a new part handles the load, but once it's gone, the metal backing plate runs straight against the cast iron: grooves appear, disc thickness drops below the minimum, and the caliper overheats. On a Mercedes with an electronic parking brake, you also get a dash error and need a scanner to retract the piston. In Almaty's city cycle with hills and dense traffic, the brakes are loaded more often than on the highway: climbs, descents and constant stops wear the linings noticeably faster, so thickness should be checked more often than the service schedule says. Timely Mercedes brake pad replacement costs less than the subsequent repair of discs and calipers. In my opinion, it's cheaper to measure the remaining friction material once than to replace discs and repair calipers later.
Replacing brake system wear items isn't just taking a part off and putting one on. On a Mercedes, caliper lubrication, a wear sensor matched to the specific model, and a correct reset of the parking brake service mode all matter.
On a Mercedes with an electronic parking brake, the rear pads are replaced only after resetting the service mode with a dealer scanner; otherwise the mechanism stays engaged and the parts won't seat properly. We have dealer scanners for 40+ makes, so we exit the mode correctly and also read ABS/ESP errors and check the sensors. We select the wear sensor for the specific model without resoldering the connector — a universal sensor triggers a brake error on the dash, and the light stays on even after replacement. Our Mercedes brake pad replacement in Almaty includes a full electronics check, so no dash errors remain after the car is handed back. In my opinion, skimping on the sensor makes no sense: a model-specific connector costs less than a repeat visit. Before handing over the car, the service advisor runs the brake system through the scanner to make sure the service mode is closed and there are no errors.
| Job option | What we replace | When it applies |
|---|---|---|
| Front axle only | Front axle linings | Disc is within spec, wear is uneven |
| Rear axle only | Rear axle linings | Rear axle wore out first |
| Linings + discs | Axle linings and discs | Disc is worn or grooved |
| Linings with sensor | Linings and wear sensor | Wear light is on the dash |
| Linings with electronic parking brake | Rear linings + mode reset | Electronic parking brake |
The time depends on whether you're replacing one axle or both, and on parts availability for your modification. Here's how to book ahead so you don't wait on a part.
The service advisor gives the exact time after diagnostics — it depends on whether it's one axle or both and on the condition of the discs. The service advisor takes in the car, and he also handles the work order from intake to handover — you don't have to retell the story to every next technician. On the lift we check lining thickness, the condition of the discs and guide pins, and bleed the circuit if the caliper was opened. For brakes we have 6 lifts and dealer scanners for 40+ makes, including Mercedes — we switch the electronic parking brake into service mode with a scanner, not "by ear." If the parts for your modification are already in stock when you arrive, the car doesn't sit waiting — so it's best to give us the modification and VIN in advance.
Before calling, owners usually worry about three things — whether they can bring their own pads, what terms the warranty comes with, and how to confirm the part was actually replaced. Let's go through each point in order.
We give you a choice — OEM, aftermarket, or customer-supplied parts — and we install whichever option the owner picks. On a Mercedes these are three different scenarios in terms of service life and on-road behavior: factory pads keep the balance with the disc, a quality aftermarket set from proven brake manufacturers lasts comparably with calm driving, and a customer-supplied kit we install with no markup and no swaps. Before installation the technician checks the part number against the VIN and inspects the disc — if the thickness is at the limit, fresh friction material will wear out in a couple thousand kilometers and you'll have to replace it again, this time together with the disc. The service warranty does not cover a part brought in by the customer: this is standard practice, and it's more honest to say so before the work, not after. The decision is up to the owner — we just show the condition of the assembly and spell out the consequences of each option.
We take a photo report at the key stages of the repair, show the old parts and hand them to the customer, and do a test drive before handover. The photos capture the condition of the disc before disassembly, the moment the new pads go in, and the lubrication of the guide pins — the shots show the caliper was actually taken apart, not just tightened. After reassembly the technician drives the car and checks that the pedal doesn't sink and that braking happens without vibration or pulling to one side. Having the old part in hand is the simplest way to be sure: the work was really done and a kit wasn't just written off the shelf — the owner can inspect the pad with its remaining thickness themselves or show it to a mechanic they know. This set of documents and parts answers the buyer's main question — what exactly they paid for.
After a pad change the pedal sometimes feels soft and the new parts squeal. We break down where the cause is the fluid and where it's just bedding in.
We change brake fluid with a full pressure bleed, not a top-off — old fluid with water in it boils under braking and the pedal sinks. The procedure for the w204 follows the same scheme: the circuit is emptied completely, not topped up with fresh fluid over the used stuff. Mercedes w204 brake pad replacement under this scheme is inseparable from a full bleed of the circuit. Moisture in the brake fluid lowers the boiling point, so the pedal goes to the floor on a long descent or after a series of hard stops, when the pads heat up the most. A pressure bleed pushes air and old fluid out of the calipers and lines at the same time, without manual pumping of the pedal. Topping up over old fluid doesn't solve the problem: water stays in the circuit and boils under hard braking, so the whole volume needs to be bled.
Here's the key stuff before a brake pad replacement on a Mercedes: signs of wear, what to expect from the technician, and the work you shouldn't skip.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost of replacing Mercedes brake pads at CARGID depends on the model and type of pads (front/rear). On average, labor for replacing front pads ranges from 5,500 to 6,500 tenge, and for rear pads from 4,500 to 5,500 tenge. We provide the exact price after diagnostics, since some models with an electronic parking brake require additional operations to reset the servo. The price includes removing and installing the wheels, cleaning the calipers, lubricating the guide pins, and checking the brake system. Other work, if needed (for example, disc replacement), is paid separately.
Usually, replacing Mercedes brake pads takes from 1 to 1.5 hours. If brake discs also need to be replaced, the time increases to 2–2.5 hours. Models with an electronic parking brake may require additional time for computer diagnostics and error reset. We try to complete the work on the day of your visit, but it's better to book in advance so the technician is ready for your arrival.
Yes, we provide a warranty on completed brake pad replacement work — 6 months or 20,000 km, whichever comes first. The warranty covers installation quality: proper pad fixation, correct caliper operation, absence of squeaks and vibrations. If problems arise due to our fault during the warranty period, we will fix them free of charge. The warranty on the pads themselves is provided by the manufacturer and depends on their brand.
Booking is recommended: different Mercedes models require their own pads, and availability is confirmed before the visit. When booking, we check the warehouse and, if necessary, order parts for the specific VIN. We can accept you without an appointment, but there may be a delay due to selecting the pads.
Yes, you can use your own pads. However, we recommend installing high-quality original or proven equivalents to ensure safety and long service life. If you bring your own parts, we are responsible only for the quality of installation, but not for the characteristics of the pads themselves. Before installation, the technician will inspect your pads for compatibility and condition. We also have our own pads in stock — this is convenient if you don't want to spend time searching.
If after brake pad replacement you notice a squeak, vibration, or worsening braking, contact us immediately. In most cases, this is related to improper bedding-in of the new pads or dirt ingress, but there can be more serious causes — for example, worn caliper guide pins. During the warranty period, we will perform diagnostics and fix the problem free of charge. Don't delay your visit, as a brake system malfunction is life-threatening.
Replacing only the pads is a standard procedure when the brake discs are still within specification (thickness within tolerance, no deep grooves or cracks). The cost of such work is lower. If the discs are worn or damaged, their replacement is mandatory; otherwise, the new pads will wear out quickly and will not provide effective braking. We always check the condition of the discs and recommend the optimal option. Replacing discs together with pads costs more, but in the long run it is more cost-effective — the brake system will work correctly longer.
The service includes: removing the wheel, dismantling the caliper, extracting the old pads, cleaning the caliper and guide pins, lubricating the guide pins with special grease, installing new pads, reassembly, bleeding the brakes if necessary, installing the wheel, and tightening the bolts to Mercedes specification torque. We also perform computer diagnostics if a service interval reset is required for the electronic parking brake. Additionally, we can check the brake fluid level for free and top it up if necessary (within reasonable limits).
After replacing the pads, for the first 200-300 km try to avoid hard braking and prolonged braking at high speed — this will help bed the pads to the discs. During this period, braking efficiency may be reduced, so keep your distance. Regularly check the brake fluid level and watch for extraneous noises. Every 10,000 km or at every maintenance, inspect the pads for wear. Avoid frequent braking on long descents — this overheats the system. It is also recommended to wash the discs and pads to remove road chemicals, especially in winter.
Payment is accepted in cash and by bank transfer; for legal entities — by invoice. The cost of the work depends on the Mercedes model, axle (front or rear pads), and whether wear sensors need to be replaced. The payment method does not affect the price.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
Had front pads replaced on a Mercedes E200. Price 85,000 tenge, everything was spot on. They resurfaced the discs and cleaned the calipers. The car brakes like new, no squeaks. Thanks for the quick work, this is my second time coming to you.
Brake pad replacement on a Mercedes GLC 300 cost 120,000 tenge. They did everything in a day and immediately checked the discs and calipers. Very attentive technicians, they explained everything. Now the brakes work perfectly, no squeaking. I recommend!
Changed brake pads on a Mercedes C220. Everything fast and high-quality, for 95,000 tenge. Replaced both rear and front. The car brakes better now, confidently. I recommend this service.
Had the brake pads replaced on a Mercedes S500. The price was 210,000 tenge, but we also replaced the discs. The work is high-quality, everything was explained. The car brakes like new. Thank you!
Had rear pads replaced on a Mercedes GLE 350d. Cost 78,000 tenge, everything was fast and neat. After replacement, the pedal became more responsive, no extraneous sounds. Special thanks for the consultation.
Changed brake pads on a Mercedes ML 350. Everything done in one day, 105,000 tenge. Quality is top-notch, the mechanics are pros. The car brakes excellently, I recommend.
Had pads replaced on a Mercedes E250. I was surprised that the discs didn't need replacing because I came in on time. The replacement cost 80,000 tenge. They worked carefully and explained everything. Now I'm not afraid of long trips.
Brake pad replacement on a Mercedes S350 — 110,000 tenge, including caliper lubrication. They did everything the same day and checked the fluid level. Very satisfied, the car brakes confidently. I will come back again.
Mercedes GLA 250, front brake pad replacement. Price 90,000 tenge, the work took a couple of hours. The technicians showed me the old pads and explained why it was time to replace them. Everything was done with quality, thank you!
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.