

Knocking in the rack of Toyota Camry
- Cause
- A knocking sound is heard on bumps, the steering wheel has become heavier.
- Found
- Wear of the insert and adjusting nut.
- Done
- Replaced the insert, nut, lubricated, adjusted.

We will restore steering precision and eliminate knocking. We repair mechanical, hydraulic, and electric racks of all makes: from Ford Transit and Volkswagen Passat to Hyundai Elantra and BMW. Diagnostics with disassembly — from 5000 ₸, repair — from 25000 ₸, warranty of 12 months. Book a convenient time — we will restore your confidence behind the wheel.
From adjustment to seal replacement — we eliminate play, knocking, and leaks in the rack

We tighten the adjusting screw and replace accessible seals right on the car. Play and knocking in the steering disappear, the rack does not need to be removed.

We disassemble the rack with electric power steering, check the electric motor and sensors, and replace worn components. The steering works precisely again, without jamming.

We flush the hydraulic system, replace seals and worn components of the rack with hydraulic power steering. Leaks, pump hum and stiff steering disappear.

We tighten the rack adjusting screw to factory torque. We eliminate steering play and knocking on uneven roads.

We replace the set of steering rack boots. We protect the shaft and seals from dust and moisture, extending the service life of the unit.

We replace the steering shaft corrugation. We restore tightness and protect the shaft from dirt, eliminate knocking in the steering column.

We replace the steering rack seals with the unit removed. We eliminate fluid leaks and dirt ingress into the mechanism.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
We show real examples of steering rack repair — what it was and how it became.
Price list for diagnostics, repair, and replacement of steering racks at the CARGID car service.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| On-site steering rack diagnostics (inspection, play, leaks) | 1 hour | 12 mo | from 5,000 ₸ |
| Steering rack diagnostics on a stand at the service center | 1–1.5 hours | 12 mo | from 7,000 ₸ |
| Tightening the steering rack adjusting screw (eliminating play) | 1 hour | 12 mo | from 4,000 ₸ |
| Replacement of steering rack boots (set) | 1–2 hours | 12 mo | from 8,000 ₸ |
| Replacement of the steering shaft corrugated boot | 1–2 hours | 12 mo | from 6,000 ₸ |
| Replacement of steering rack oil seals (with the rack removed) | 2–3 hours | 12 mo | from 12,000 ₸ |
| Steering rack repair without removing it from the vehicle (tightening, oil seals) | 2–3 hours | 12 mo | from 10,000 ₸ |
| Replacement of the steering rack repair kit (bushings, oil seals) with removal | from 4 hours | 12 mo | from 25,000 ₸ |
| Grinding/polishing of the steering rack rod (if there are no deep scores) | 1–2 hours | 12 mo | from 5,000 ₸ |
| Elimination of steering rack leak (replacement of oil seals, gaskets) | 3–4 hours | 12 mo | from 15,000 ₸ |
| Adjustment of steering effort (after repair) | 30 minutes | 12 mo | from 3,000 ₸ |
| Replacement of the steering rack with a used one (with removal/installation) | from 4 hours | 12 mo | from 20,000 ₸ |
| Replacement of the steering rack with a new one (for passenger cars) | 4–6 hours | 12 mo | from 25,000 ₸ |
| Replacement of the steering rack with a new one (for crossovers/SUVs) | 5–8 hours | 12 mo | from 35,000 ₸ |
| Removal and installation of the steering rack (as a separate operation) | 3–5 hours | 12 mo | from 15,000 ₸ |
| Steering rack overhaul with replacement of all worn components | 1 day | 12 mo | from 40,000 ₸ |
| Repair of steering rack with electric power steering (EPS) | from 5 hours | 12 mo | from 30,000 ₸ |
| Repair of steering rack with hydraulic power steering (HPS) (flushing, replacement of components) | from 5 hours | 12 mo | from 28,000 ₸ |
| Urgent steering rack repair (same day) | 5–6 hours | 12 mo | +50% to the cost |
| On-site steering rack repair (within Almaty) | from 2 hours | 12 mo | from 15,000 ₸ |
Prices are for labor only, excluding the cost of parts and consumables. The exact cost depends on the make/model of the car and the complexity of the defect. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
After disassembly, we wash the rack, measure clearances with a bore gauge and check the shaft for wear. Without measurement, tightening the screw is a lottery.
We disassemble electric and hydraulic racks according to their own scheme. We do not touch the force sensor and spool valve unnecessarily.
Without removing the rack from the car, we perform tightening and replacement of boots within a shift. For a removed rack — within 24 hours.
We cover rack repair and replacement of seals with boots. If it leaks due to our assembly, we will redo it for free.
From diagnostics to final check — a transparent steering rack repair process at CARGID.

You leave a request on the website or call — we select a convenient time for your visit. We check play, leaks, steering effort and scan for errors — we determine the exact cause.
request on WhatsApp
We state the cost of work and parts, fix the deadlines and proceed after your consent.
inspection and diagnosticsWe remove the steering rack, wash and fully disassemble it to assess its condition.
estimate before work starts
We measure wear of bushings, seals and shaft — we report what needs to be replaced.
work to factory procedureWe install new components: seals, bushings, boots, adjusting shims.
result check
We assemble the rack, adjust the engagement of the shaft and rack for precise steering. We install the rack, check on the lift and test — we return the car to you.
warranty in the work orderWalk-ins welcome. By appointment — no queue.
CARGID car repair team. 8–17 years of experience.
Author
Mobile auto electrician

Car alarm and car stereo installer

Auto electrician

Roadside assistance technician

Diagnostic technician

Engine mechanic (cylinder head repair)

Auto electrician and diagnostician

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

CARGID repairs steering racks in Almaty with a 12-month warranty: first diagnostics and a written estimate, then the work. We tighten the adjusting screw, replace seals and dust boots, polish the shaft, rebuild the rack, and repair racks with EPS and hydraulic power steering. Without removal — same shift, removed rack — next day.
A symptom alone doesn't name the job — a rattle over bumps, a leak under the dust boot and a tight steering wheel lead to different work. Here's how a technician separates the rack from the suspension and what gets measured.
On the lift we check the rack and the tie rods separately: shaft play and rattle are heard when the steering wheel is rocked, while tie rods show themselves with an axial push on the wheel. The technician grabs the wheel at the 3 and 9 o'clock positions and rocks it — that's how wear in the tie rod ends is heard, and rocking the steering wheel in place reveals play in the gear mesh. After disassembly we wash the part, measure clearances with a bore gauge and check the shaft for wear — without measuring, adjusting the adjusting screw turns into a lottery. Over 9,000+ cars have come through our shop in 12 years, and we've seen more than once how adjusting "by ear" finished off the bushings. If the noise is heard only on small bumps and disappears at speed, the wear inside the bushings is more often to blame than the tie rod ends — so no verdict can be made without disassembly and measuring clearances with a bore gauge.
Oil under the dust boot is a sign of worn seals, while a tight steering wheel with a whine more often points to the power steering pump and the condition of the fluid, so we check both. We lift the car, look at the dust boots for tears and signs of seepage, and check the fluid level and color in the reservoir: darkened fluid with a burnt smell means the pump has overheated. We fix the leak by replacing the seals and O-rings — with the rack removed this takes less time than it seems. We inspect the pump separately: if it already whines under load, replacing the seals alone won't bring back normal steering effort. You can't drive with a leak for long: the fluid runs out, the pump runs dry and adds a pump replacement to the job — so it's better to show the leak before the steering gets heavy.
Some jobs are done right on the car and take a shift, while others require removing the rack and a full day. We separate them by fact so you know what to expect in terms of time.
Without removal we adjust the adjusting screw and replace the dust boots and the steering shaft boot — that fits into a shift and doesn't require disassembling the rack. This kind of steering rack repair in Almaty takes care of the knocking over bumps and protects against dirt, but not a leak. The adjusting screw takes up play in the gear mesh, while the dust boots and boot protect the shaft and the steering shaft from dust and moisture. You can't reach the seals and bushings from under the dust boot, so if the cause is there, the rack still has to be removed. In my opinion, adjusting the screw only makes sense after measuring clearances with a bore gauge — otherwise it's a lottery, not a job. Before starting, the service advisor shows the worn dust boots and explains what the adjustment will and won't fix.
We get the removed rack back in shape within 24 hours: replacing the seals and the repair kit, polishing the shaft and rebuilding are done on the bench, not on the car. After disassembly we wash the part, measure clearances with a bore gauge and check the shaft for wear — based on these measurements we decide whether the repair kit is enough or polishing is needed. One day is the time for the work on the rack, not the car sitting in a queue: the service advisor handles the work order from intake to handover, so the removal and installation time is known in advance. We show the old seals and bushings and give them to the customer so it's clear what was replaced. The warranty on this work is 12 months, and its term and conditions are written into the work order. Before handover we do a test drive and check the steering effort.
| Operation | Unit removal | What it fixes | Timeline |
|---|---|---|---|
| Adjustment screw tightening | no | play, knocking | same day |
| Boot and bellows replacement | no | dirt, protection | same day |
| Seal replacement | yes | leak | one day |
| Shaft grinding | yes | scoring, shaft leak | one day |
| Rebuild with repair kit | yes | bearing wear | one day |
Electric and hydraulic racks are built differently, so we approach each one its own way. Here's where the difference lies and which components we don't touch unnecessarily.
In a unit with electric power steering, we check the electric motor and torque sensor with a scanner, and we only open up the mechanicals based on the readings — no unnecessary work. Dealer scanners for 40+ brands read motor errors and shaft position, and after disassembly we measure gear mesh clearances with a bore gauge and assess shaft wear. We remove the electric motor and check it separately: winding, brushes, contact resistance. If there's no confirmed defect, we leave the torque sensor and spool valve in place — unnecessary disassembly throws off calibration and adds play. Steering binding here doesn't always mean unit replacement: often it's the torque sensor calibration, and we restore it without opening the housing. In my opinion, it's the electronics that produce the most false rack verdicts.
In a rack with hydraulic power steering, we flush the hydraulic system, replace seals and O-rings, and only open the spool valve if wear is confirmed. We flush with the rack removed, pour in fresh power steering fluid and bleed the circuit to push out air and old debris. We check the pump by pressure and by whining under load, and we replace seals as a set — a single seal replacement doesn't hold. Pump whine and a stiff steering wheel aren't always the rack's fault: after flushing and fluid replacement some symptoms go away and the components stay in place, so we start by checking pressure and fluid condition. After disassembly we grind the shaft if there's no deep scoring, and we fix leaks under the boot by replacing seals before the pump runs dry. In our practice, half of hydraulic complaints end with a flush and seals, without replacing the rack itself.
The line between restoration and replacement depends on the condition of the shaft and housing, not on mileage. Here's what the technician decides after disassembly and measurement.
Tightening the screw helps as long as bushing wear is within tolerance: after disassembly we wash the unit, measure clearances with a bore gauge, and only then decide whether tightening is enough. The adjustment screw presses the shaft against the bushings and removes play, but the clearance itself doesn't go away — it just stops knocking on bumps. If the bore gauge shows bushing wear beyond tolerance, tightening gives a temporary effect for a couple of weeks, and then the knock comes back stronger. That's why at CARGID we first disassemble the unit, wash the parts and check the shaft for wear, and we make the tightening verdict based on three measurements. Without measurement, tightening the screw is a lottery: over-tighten and the steering gets stiff and the mechanism wears faster; under-tighten and the knock returns in a month.
We grind and polish the shaft if the scoring isn't deep: after treatment the seal sits on a clean surface and the leak stops. Shaft scoring comes from sand under the boot and from old fluid with metal shavings — the seal catches on the roughness and lets oil through. We remove the unit, assess the depth of scoring, and only on a clean surface under the seal do we install a new seal. If wear has reached the housing, shaft grinding won't help. Deep scoring and housing wear can't be fixed by grinding — there we install a used or new part so we don't come back to a leak in a couple of months. Shaft grinding costs less than unit replacement and preserves the original housing if wear is within tolerance.
Before work, the client sees an estimate, and on delivery — a warranty in the documents. Here's how the process works and what exactly the rack warranty covers.
First we do diagnostics and a written estimate, and we start work only with the client's consent; parts can be OEM, aftermarket, or client-supplied. The service advisor records the symptom, the technicians check play, leaks and boot condition, then the work order lists operations with details: adjustment screw tightening, seal replacement, shaft grinding, or rebuild with a repair kit. Each item is listed separately, so the owner sees in advance what the work consists of and which components we touch and which we leave. The choice of material is theirs: OEM lasts longer, aftermarket is cheaper, and we also accept their own parts. Until the estimate is approved, the car stays put and no one disassembles the rack. We install client-supplied parts, but the warranty doesn't cover them — it's worth knowing in advance to avoid a dispute at pickup.
We give a 12-month warranty on steering rack restoration and record the term and conditions in the work order and the acceptance certificate when the car is handed over. The coverage applies to the work performed and the parts we install: adjusting the screw, replacing seals and boots, a rebuild with a repair kit, and polishing the shaft. It does not cover an accident after the work, tampering by third parties, or a part the customer brought in themselves. Diagnostics for a warranty case is free with us — if the knock or leak comes back, the technician rechecks the rack on the test stand and verifies the clearances with a bore gauge instead of just tightening the screw again. The term and conditions are written into the documents at handover, so in a disputed situation all you have to do is open the work order and check exactly what was done. This approach removes the main risk: the customer isn't left alone with a defect a month after the work.
Steering rack repair means choosing the right operation for the specific wear, not a one-size-fits-all procedure. Below is a short summary to help you decide before your visit to the lift.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost of steering rack repair at CARGID depends on the car make and the complexity of the breakdown. Premium brands (BMW, Mercedes-Benz, Audi) — from 150000 tenge and above. The exact price will be quoted by the technician after diagnostics, which costs 5000 tenge (free with repair). The price already includes all work and replaced seals, oil seals, and dust boots. You receive the full list and final estimate before work begins — no hidden extra charges. Exact prices are in the price list on this page.
On average, steering rack repair takes from 3 to 6 hours. It all depends on complexity: if only a dust boot or seal needs replacement, we'll finish in 2–3 hours. For a complete rebuild with replacement of bushings, bearings, and adjustment, it may take 5–6 hours. Don't forget to add 30–40 minutes for diagnostics and post-repair check. In complex cases (for example, if the rack is from an impact or rare parts are needed), the time may increase to 1–2 days, but we usually order the necessary components in advance or use proven analogs so as not to delay your car.
Yes, we provide a warranty on all types of work — 12 months or 15,000 km, whichever comes first. The warranty covers seal tightness, absence of knocks and play, and correct operation of the mechanism. Important: the warranty is valid if you follow the operating recommendations and regularly check the dust boots and the fluid level in the power steering reservoir. If you notice a malfunction during the warranty period, just come in — we will fix the problem or replace parts free of charge if the cause is our repair.
An appointment is desirable: separate time is allocated for steering rack diagnostics to check play, knocks, leaks, and the condition of dust boots on the lift. Diagnostics takes from 30 to 60 minutes depending on the rack design — with hydraulic or electric power steering. Based on its results, the scope of work is agreed: replacement of seals, bushings, engagement adjustment, or shaft restoration.
Yes, you can provide your own parts. We will accept them, but first check compatibility and quality. However, it's important to understand: if the part turns out to be unsuitable or used, we are not responsible for it and do not provide a warranty for its operation. Steering rack repair usually requires seals, dust boots, repair kits, bushings — we recommend using quality analogs (for example, from CTR, Febi, SKF), which are in stock. If you bring your own, we can install them with a warranty only on the work, not the part.
If the rack was repaired elsewhere and knocks, play, or leaks appeared, we can perform diagnostics and fix the defects. Diagnostics costs 5000 tenge. If the problem is serious — for example, the stop is set incorrectly or the bushings are worn — we will suggest rebuilding the rack again. Our technicians always perform a control adjustment after assembly, so such problems are rare for our clients. If you decide to repair with us, the cost of work will be as for a new repair, but we will give a 10% discount for a repeat visit.
There are many options for steering rack repair: partial (replacement of dust boots, seals) — quick and inexpensive; major (complete rebuild with replacement of all worn elements) — more reliable and durable; replacement of the rack with a new or rebuilt one (if the housing is damaged). We always offer the optimal option based on the condition of the rack. Partial repair will cost from 35000 tenge, major — from 40000 tenge. Replacement with a new rack will cost from 25000 tenge (depending on the model). Prices for repair kits are included in the cost of work or listed separately.
After steering rack repair, it is important to follow several rules. First, regularly check the oil level in the power steering reservoir (once a month) — if the level drops, immediately look for leaks. Second, do not hold the steering in the extreme position for more than 5 seconds — this can cause the pump to overheat. Third, have suspension and steering maintenance every 15000 km: check dust boots and tightening. Avoid sharp impacts on the wheels, especially on bumps. In rainy weather and when washing, make sure the dust boots do not let water through. If a knock or leak appears — come to the service for inspection.
Payment is accepted in cash and by bank card, transfer is possible; final payment is made after the work is completed. The cost depends on the type of rack (mechanical, hydraulic, electric), the list of replaced parts, and whether the rack needs to be removed from the car. The cost of the repair kit and consumables — power steering fluid, seals, dust boots — is calculated separately. The exact amount is quoted after diagnostics and agreement on the scope of repair.
Yes, you can operate the car immediately after repair, but for the first 500 km we recommend a gentle mode: avoid sharp maneuvers, off-road driving, and heavy loads on the steering when parking. When leaving the service, be sure to drive for 10–15 minutes so the oil distributes through the system. If you replaced the seals, in the first days there may be slight lubrication, which is not a leak — it is acceptable. After 1000 km, we recommend returning for a repeat check (free) to control tightening and absence of leaks.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
I came in with a steering rack leak on a Kia Rio. Diagnostics showed the seals were shot. They replaced all seals, bushings, and dust boots as well. The price was 85000 tenge, done in a day. The car steers like new, no leaks. I liked the service, everything was explained, old parts were shown.
The steering wheel on my car became hard to turn. We repaired the steering rack at CARGID. The bearing was replaced, grease applied. The price was 55000 tenge, done in one day. Now the steering turns easily. Thank you!
A knocking appeared in the steering rack on my Toyota Camry. I came to CARGID, diagnostics showed wear on the bushing. They replaced the bushing and nut, and adjusted it. They worked one day, I paid 62000 tenge. The knock is gone, the steering is precise. I recommend!
The Nissan X-Trail started leaking power steering fluid. At the service they said the seals were dead. They replaced the shaft and housing seals, flushed the system, and filled new fluid. It took 78000 and two days. Now it's dry under the car, the steering wheel turns easily. Thanks for your patience, everything was explained in a human way.
There was steering play on the Chevrolet Cruze. At CARGID they adjusted the engagement, replaced the tie rod end. Done in a day, price 48000 tenge. The steering has no play, the car drives straight. Very pleased with the quality of work!
Toyota Corolla, the steering became heavy and a crunch appeared. It turned out the steering rack shaft bearing had fallen apart. They replaced the bearing, lubricated, adjusted. 55000 tenge, one day. Everything was clear, they even washed the car before pickup. I will recommend!
Hyundai Creta had steering vibration, an error was lit on the dashboard. Diagnostics showed a short circuit in the electric motor. They replaced the motor, flashed the unit. I paid 120000 tenge, they did it in two days. Now everything works perfectly, no errors. Great job, no problems at night.
Volkswagen Polo, the steering wouldn't turn normally, there were jerks. Diagnostics revealed worn seals. They replaced the seals, bushings, dust boots. Price 78000, done in 1 day. Now the steering is soft, control is precise. Excellent service, polite technicians.
The rack was leaking on a Kia Sportage. Repaired at CARGID: replaced seals, bushings, dust boots. Done in a day, cost 85000 tenge. Everything to the point, no imposed services. The rack is dry, the steering is light. Thanks, I recommend!
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.