Authorexperience

Mercedes transmission requires regular fluid changes. At CARGID, original or a verified equivalent of your choice is used to ensure uninterrupted operation of the automatic transmission. Contact us — we will extend the life of your transmission!
All types of Mercedes automatic transmission fluid changes — from partial to valve body repair

We change the oil using the displacement method via a machine, without touching the pan. The old oil is completely replaced with fresh.

We remove the pan, drain the old oil, replace the transmission filter, and clean the magnets. Then we fill with new oil.

We drain the oil, remove the pan, and replace the pan gasket with a new one. We eliminate leaks and fill with fresh oil.

We remove the valve body, clean it from contaminants and metal shavings, and change the oil. We restore shift clarity.

We change the oil and perform transmission adaptation: reset old settings and relearn under the new oil.

Complete set: drain the oil, remove the pan, replace the filter and gasket, clean the magnets. Fill with new oil.

We change the oil and the solenoid valves (solenoids) in the valve body. We eliminate jerks and shifting delays.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
Current prices for automatic transmission fluid change for Mercedes at the CARGID auto service.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Automatic transmission diagnostics (computerized, without pan removal) | 30–40 min | 6 mo | from 5,000 ₸ |
| Visual inspection of the automatic transmission for fluid leaks | 15–20 min | 6 mo | from 2,000 ₸ |
| Removal and installation of the crankcase protection (if present) | 30–40 min | 6 mo | from 3,000 ₸ |
| Partial automatic transmission fluid change (drain through plug, fill to level) | 1–1.5 hours | 6 mo | from 8,000 ₸ |
| Automatic transmission fluid change with complete flushing (without pan removal) | 1.5–2 hours | 6 mo | from 15,000 ₸ |
| Automatic transmission fluid change with pan removal and filter replacement | 2–2.5 hours | 6 mo | from 20,000 ₸ |
| Automatic transmission fluid change with pan gasket replacement | 2–2.5 hours | 6 mo | from 18,000 ₸ |
| Automatic transmission fluid change with valve body flushing | 3–4 hours | 6 mo | from 30,000 ₸ |
| Automatic transmission fluid change with automatic transmission adjustment (adaptation) | 3–3.5 hours | 6 mo | from 25,000 ₸ |
| Automatic transmission fluid change with gasket and filter replacement (full kit) | 2.5–3 hours | 6 mo | from 22,000 ₸ |
| Automatic transmission fluid change with solenoid valve replacement | 4–5 hours | 6 mo | from 45,000 ₸ |
| Automatic transmission fluid change with torque converter replacement | 5–6 hours | 6 mo | from 60,000 ₸ |
| Automatic transmission fluid change with hydraulic plate (valve body) repair | 4–5 hours | 6 mo | from 50,000 ₸ |
| Urgent automatic transmission fluid change (within 2 hours, advance booking required) | 2 hours | 6 mo | from 25,000 ₸ |
| Mobile automatic transmission fluid change (at client's address, within Almaty) | 2–3 hours | 6 mo | from 35,000 ₸ |
| Automatic transmission fluid change on vehicles with engine displacement up to 2.0 | 2 hours | 6 mo | from 12,000 ₸ |
| Automatic transmission fluid change on vehicles with engine displacement from 2.0 to 3.0 | 2–2.5 hours | 6 mo | from 15,000 ₸ |
| Automatic transmission fluid change on vehicles with engine displacement from 3.0 | 2.5–3 hours | 6 mo | from 18,000 ₸ |
| Automatic transmission fluid change on Mercedes SUVs (GLC, GLE, GLS) | 2.5–3 hours | 6 mo | from 20,000 ₸ |
| Automatic transmission fluid change with complete transmission disassembly and inspection | from 1 day | 6 mo | from 80,000 ₸ |
Prices are for labor only, excluding the cost of fluid, filters, and consumables. The exact cost is determined by the technician after diagnostics. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
During a partial change, about 6 liters out of 9 are drained. A double drain with intermediate flushing displaces old fluid from the valve body, not just from the pan.
Before checking, we warm up the transmission to 45 °C and verify the level via the control plug. If done cold, you get foaming.
We reset adaptations with a scanner and run through the gears in manual mode. The unit relearns shift points, and jerks disappear.
After removing the pan and replacing the filter, we give a 6-month warranty for tightness and operation of the unit. We measure the level at 45 °C through the overflow plug.
We explain how the oil change in a Mercedes automatic transmission is carried out at our service.

You submit a request on the website or by phone, and we select a convenient time for your visit. We perform computer diagnostics and inspect the transmission to determine the condition of the oil and filters.
request on WhatsApp
We carefully drain the old oil through the drain hole and assess its condition.
inspection and diagnosticsWe remove the pan, clean the magnets from metal shavings, and replace the transmission filter.
estimate before work starts
We wash the pan and check the condition of the gasket, replacing it if necessary.
work to factory procedureWe pour fresh oil recommended for your Mercedes model through the filler hole.
result check
We warm up the transmission, set the oil level to the norm, and check the shifting. We perform a test drive, hand over the keys, and give recommendations for further maintenance.
warranty in the work orderWalk-ins welcome. By appointment — no queue.
CARGID car repair team. 8–17 years of experience.
Author
Mobile auto electrician

Car alarm and car stereo installer

Auto electrician

Roadside assistance technician

Diagnostic technician

Engine mechanic (cylinder head repair)

Auto electrician and diagnostician

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

CARGID in Almaty changes Mercedes automatic transmission fluid with diagnostics, pan removal, filter and gasket replacement, valve body cleaning, and transmission adaptation. You get a written estimate first, then the work. The transmission fluid change warranty is 6 months; the timeframe and terms are fixed in the work order and the acceptance certificate when you pick up the car.
The Mercedes transmission fluid change interval depends on the transmission type and driving conditions. In Almaty traffic, the fluid ages faster, so the mileage guideline shifts downward.
The manufacturer recommends changing the fluid in a Mercedes 7G-Tronic automatic transmission at around 60 thousand km, but in dense Almaty city driving it makes sense to shorten the interval to 40–50 thousand km. The 722.9 unit is found in most rear-wheel-drive models, the newer 725.0 (9G-Tronic) in newer generations, and the same logic applies to both: the more heat cycles and stops, the faster the ATF additives degrade. On the highway, the fluid lasts longer; in city traffic with frequent starts and short trips, noticeably less. Short winter trips are especially harmful: the unit doesn't reach operating temperature, condensation gets into the pan, and the emulsion accelerates friction disc wear. Mileage alone isn't the indicator—the number of heat cycles and traffic jams matters more, so if you drive downtown often, aim for the lower limit, not the upper one.
We explain how a partial drain of Mercedes transmission fluid differs from a machine flush, how much fluid actually comes out of the unit, and why the pan and filter should be removed during the process.
With a partial drain, about 6 liters out of 9 come out—a double cycle with intermediate pumping displaces old fluid from the valve body, not just the pan. A regular single drain only removes 3 liters, leaving almost half of the old fluid in the channels. We do two cycles: drain the first portion, pump the unit, then drain the second, and only after that fill with fresh fluid. This approach takes more time than a single procedure, but the concentration of old fluid drops significantly lower. The machine method under pressure displaces a larger volume, but without removing the pan, you can't check the magnets or replace the filter—so we combine draining with pan inspection and consumable replacement. Our Mercedes automatic transmission fluid change in Almaty always includes level control and a check of the unit's operation after the procedure.
| Option | What's included | When needed |
|---|---|---|
| Change with pan removal and filter | drain, filter, gasket, level check | basic service |
| Change with pan gasket | drain, gasket, level check | pan removed, filter fresh |
| Change with valve body cleaning | drain, valve body cleaning, filter | valve body contamination |
| Change with transmission adaptation | drain, reset adaptations, gear run | jerks after change |
| Change with solenoids | drain, solenoid replacement, adaptation | solenoid wear |
| Change with valve body repair | drain, valve body repair, assembly | scoring, channel wear |
The ATF specification depends on the transmission type, so we first determine what's in the car and only then select the fluid. Below is how we do it and which MB specifications correspond to each transmission.
We identify the transmission type by VIN and scanner—dealer-level scanners for 40+ brands read the transmission ID, and from that we select the fluid specification. The five-speed 722.6 (5G-Tronic) was installed in previous-generation cars; the seven-speed 722.9 (7G-Tronic) and nine-speed 725.0 (9G-Tronic) look almost identical from the outside—the difference is in the pan marking and electronics. We look up the unit number by VIN, the scanner confirms the control unit version, and only then does the technician write the required ATF specification in the work order. Getting the transmission type wrong is the most common cause of "incorrect" fluid: the externally similar 722.6 and 722.9 require different specifications, and the wrong ATF shows up as jerks within a few thousand kilometers. In my opinion, checking by VIN takes a couple of minutes and eliminates the risk of using the wrong fluid. This is exactly what determines which Mercedes transmission fluid change is needed and how much fluid will be required.
| Transmission type | Model | MB specification |
|---|---|---|
| 5G-Tronic | 722.6 | MB 236.14 |
| 7G-Tronic | 722.9 | MB 236.15 |
| 9G-Tronic | 725.0 | MB 236.17 |
A fluid change relies on two steps where corners are most often cut—level measurement and adaptation. We explain why fresh fluid doesn't deliver results without them.
Before checking, we warm the transmission up to 45 °C and verify the level at the check plug — when it's cold, the fluid foams and the reading lies. On the 722.6, 722.9 and 725.0 gearboxes there's no dipstick in the pan, so the volume is set by the overflow plug: a steady stream should come out of it. Until the unit reaches operating temperature, the fluid is thicker and takes up less volume — topping up "by eye with a dipstick" leads to underfilling or overfilling. Overfilling is more dangerous than underfilling: the excess pushes out the seals and foams when it heats up, so we set the level strictly by the plug, not by eye. After measuring we always take the car for a drive and repeat the check — over the first kilometers the fluid spreads through the valve body channels. In my experience, it's that second check that rules out half of the disputed cases.
We reset the adaptations with a scanner and run through the gears in manual mode — the unit relearns the shift points and the jerking goes away; this takes about 40 minutes. Fresh fluid changes the pressure in the valve body, and the old adaptation values were calculated for worn fluid, so without a reset the gearbox keeps working to the old points and jerks. After the reset the unit picks the shift timing for the new pressure on its own — on the 7G-Tronic this is noticeable on the very first drive. If the jerking remains after the fluid change, the problem is no longer the fluid but the valve body or the solenoids — that calls for diagnostics, not another fluid change. Our warranty on this work is 6 months; the term and conditions are recorded in the work order.
We show you how the process works before the repair starts and when the car is handed over: where the owner sees the result, what the warranty covers and how things change if they bring their own parts and fluids.
First we run diagnostics and prepare a written estimate, and we start work only after the client agrees; we keep a photo report of the key stages. The car is received by the service advisor, who handles the work order through to handover — one person is responsible for the entire scope of transmission work. The estimate includes removing the pan, the filter, the gasket, valve body flushing and adaptation: the owner sees the full list of items in advance, not individual lines added along the way. We show the removed parts and the condition of the pan magnets and give them to the client — the metal shavings on the magnets show how worn the gearbox is. That inspection is more convincing than any promises: it shows the unit's remaining life before the owner decides whether to stick with servicing or prepare for a repair. The photo report also makes it easy to recall later exactly which parts were replaced and what condition the internals were in.
We've put together the full picture of what determines the result of a Mercedes transmission fluid change: the schedule for the gearbox type, the real fluid volume, the level check and the unit adaptation.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost of Mercedes automatic transmission fluid replacement at CARGID depends on the car model, the type of automatic transmission (torque converter or DSG), and the replacement method. A partial replacement (fluid replacement in the pan) will cost from 15,000 to 25,000 tenge, a full machine replacement (with flushing) — from 15,000 tenge. The exact price can only be given after diagnostics on a lift, since Mercedes uses different types of gearboxes and transmission fluids that differ in price. The final cost includes labor and consumables (fluid, filter, pan gasket).
For a partial fluid replacement, the work will take about 1–1.5 hours. A full machine replacement with system flushing takes more time — from 2 to 3 hours, since it is necessary to run several liters of fluid through the system, remove the pan, replace the filter and gasket. If you additionally need to remove the engine protection or perform defect detection, the time may increase. We always inform the client about the timing in advance and recommend leaving the car for half a day so as not to rush and do the work with quality.
The warranty is provided for the work of replacing the automatic transmission fluid and filter: the term is 6 months or 10,000 km of mileage, whichever comes first. It covers the correctness of installation of the pan, gasket and filter, as well as the absence of leaks after the procedure. The fluid and filters themselves are covered by the manufacturer's warranty, so keep the packaging and receipt.
An appointment is desirable: different Mercedes models require different volumes of fluid and filters, as well as a lift for 1.5–3 hours. Without an appointment, we will accept the car if there is a free lift and the necessary consumables in stock. To avoid waiting, it is better to agree on the date and time by phone a day or two in advance.
You can, if the fluid and filter meet Mercedes specifications for your automatic transmission model (for example, 722.6, 722.9, 7G-Tronic). We will check the part numbers by VIN and warn you if the consumables are not suitable. The cost of work in this case is fixed, and the warranty for the brought parts applies only from their seller.
We value our reputation and provide a warranty for work of 6 months or 10,000 km. If after fluid replacement you find a leak, extraneous noises or errors in the automatic transmission operation, we will conduct a free repeated diagnostics and eliminate the defect. We also photograph the replacement process and can show the condition of the pan and magnets — you see how much metal shavings and deposits there were. All work is performed according to Mercedes regulations, using professional equipment. If the claim is justified, we will correct the situation without additional payment — this is stated in our warranty coupon.
Partial replacement is draining the old fluid through the drain plug (or removing the pan) and pouring in new. In this case, up to 30–40% of the old fluid remains in the torque converter and valve body, meaning the fluid is not completely renewed. Full machine replacement is carried out using a special stand that displaces the old fluid under pressure and simultaneously pours in new. This method allows replacing up to 95% of the fluid and cleaning the system from contaminants. Machine replacement is more expensive but more effective, and is recommended for high mileage or if the old fluid is heavily contaminated.
After automatic transmission fluid replacement, we recommend avoiding aggressive driving style and towing a trailer for the first 500–1000 km so that the fluid is evenly distributed throughout the gearbox elements. It is also worth checking the fluid level a few days after replacement, especially if it was a partial replacement. You need to drive with a fully warmed-up gearbox, switching all modes to eliminate air pockets. In the future, follow the replacement schedule specified in the Mercedes service book (usually every 60,000 km or 4 years for automatic transmissions, but for some models — 40,000 km).
We accept cash, bank cards (Visa, Mastercard, Elcart), as well as non-cash payment for legal entities. Payment is made after the work is completed — you accept the car, check everything, and only then pay. If you need a receipt or invoice, we will provide all necessary documents. When ordering a full fluid replacement, prepayment for materials (fluid, filters) is possible if they were not purchased in advance. For regular customers, there is a system of discounts and bonuses.
The main signs: jerks and jolts when shifting gears, delays when engaging D or R modes, increased noise from the gearbox, burnt smell from the fluid, fluid leaks on the pan or on the automatic transmission housing, as well as vibrations on the body. If you notice any of these — do not postpone your visit to the service. In Mercedes, automatic transmission fluid replacement is recommended every 60,000 km, but with active city driving in Almaty traffic jams, it is better to reduce the interval to 40,000 km. Timely fluid replacement significantly extends the gearbox life and prevents costly repairs.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
I changed the automatic transmission fluid on my Mercedes E350. I liked the service: diagnostics were done immediately, they showed me the old fluid and filter. The replacement took one day and cost 85,000 tenge. After the replacement, the gearbox shifts smoothly, the jerks are gone. I recommend it.
I came for automatic transmission fluid replacement on a Mercedes GLE 350. The guys explained everything, found no defects, but replaced the fluid with the filter. They finished in a day, price 65,000. Now the car drives like new. Thanks!
Mercedes C200 2008, high mileage. I asked to replace the automatic transmission fluid. The mechanics removed the pan — it was scary in there: metal shavings, sludge. They cleaned everything, replaced the filter and gasket. It came to 90,000, but now the gearbox works perfectly. I recommend it to those who value quality.
They changed the automatic transmission fluid on a Mercedes S500. A serious approach: computer diagnostics, filter replacement, adaptation. The car began to shift softly, the jerks disappeared. The price of 120,000 is normal for such a car. Very pleased with the service.
On a Mercedes GLK 220 I changed the fluid according to the schedule. They did it quickly, in one day, and poured in original fluid. Price 70,000. All work was itemized, I could see how the old fluid was drained. Now the gearbox works quietly and smoothly. I recommend it!
Mercedes CLS500 client, here the fluid is in the gearbox. Everything was done with quality, the filter and gasket were replaced, the leak was fixed. The work took 2 days, cost 95,000 tenge. The gearbox now works without complaints. Thank you!
Altay, I changed the automatic transmission fluid on a Mercedes E350. Everything was done at a high level, but it took two days because of a leak. In the end everything is ok, the gearbox works perfectly. Price 95,000, I think it's normal.
I changed the transmission fluid on a Mercedes C300. The mechanics know their business: they removed the pan, cleaned it, replaced the filter. Driving became much smoother. Price 75,000, finished in a day. Satisfied, I will come again.
I brought a Mercedes GLC 300, 2017. Fluid replacement according to the schedule. They work very carefully, showed and explained everything. They poured in fluid, changed the filter. The car is now like new. Price 80,000, acceptable. I recommend it to everyone.
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.