

Land Rover Discovery 4
- Cause
- Grinding noise when braking, pads worn down to zero.
- Found
- Front pads worn down to metal, discs scored.
- Done
- Replaced front pads and brake discs, lubricated the guide pins

Worn pads cause poor braking and disc damage. We replace brake pads on all Land Rover models, including Range Rover and Discovery, in 1 hour. We provide a 6-month warranty on labor. We use original and high-quality aftermarket parts — we'll help you choose according to your budget.
Full range of Land Rover brake system services: pads, discs, fluid, parking brake and wear sensors

We remove the caliper, take out the old pads, clean and lubricate the guides. We install new pads and reassemble the assembly.

We remove the rear caliper, replace the pads, service the guides and piston. We check the parking brake operation.

We replace all four pads simultaneously — front and rear. This ensures even braking and extends the life of the discs.

We remove the old discs, clean the hub, install new ones. We check runout and tighten to the required torque.

We replace the rear discs, clean the seating surfaces, check the parking brake operation. We install new discs and reassemble the assembly.

We drain the old fluid, bleed the system, fill with new. We remove air and check the tightness of the circuits.

We disassemble the drum mechanism of the parking brake, replace the shoes, adjust the drive. We check holding on a slope.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
Using real jobs as examples, we show how brake pads are replaced on a Land Rover.
We will provide the exact cost after inspection, but use these figures as a guide.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Front brake pad replacement | 1 hour | 6 mo | from 12,000 ₸ |
| Rear brake pad replacement | 1–1.5 hours | 6 mo | from 12,000 ₸ |
| Brake pad set replacement (4 pcs) | 2 hours | 6 mo | from 20,000 ₸ |
| Front brake disc replacement | 2 hours | 6 mo | from 20,000 ₸ |
| Rear brake disc replacement | 2 hours | 6 mo | from 18,000 ₸ |
| Brake pads and discs replacement, comprehensive | 3 hours | 6 mo | from 35,000 ₸ |
| Brake fluid replacement | 1–1.5 hours | 6 mo | from 8,000 ₸ |
| Brake bleeding | 1 hour | 6 mo | from 5,000 ₸ |
| Caliper guide lubrication | 1 hour | 6 mo | from 6,000 ₸ |
| Caliper repair (repair kit replacement) | 1.5–2 hours | 6 mo | from 15,000 ₸ |
| Parking brake (shoes) replacement | 1.5 hours | 6 mo | from 15,000 ₸ |
| Brake system diagnostics | 30–40 min | 6 mo | from 3,000 ₸ |
| Brake pad wear sensor replacement | 30 min | 6 mo | from 3,500 ₸ |
| Brake hose replacement (1 pc) | 1 hour | 6 mo | from 4,000 ₸ |
Prices do not include the cost of parts. The exact price depends on the Land Rover model and complexity of work. Please check with the manager. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
We install all four pads of one axle at once, not one by one. Otherwise, different friction pulls the car to the side when braking.
We run fresh fluid through the circuit under pressure, drain the old from each caliper. Moisture in the old fluid boils and the pedal sinks.
The old sensor no longer works after removing the pads. The new one lights up the lamp in advance, and you manage to book before metal.
We stand behind the assembly for six months: squeaks, runout, pulling when braking — we redo it at our own expense. This does not apply to the pads themselves.
We explain how brake pad replacement on a Land Rover goes in our service — from booking to vehicle handover.

You leave a request on the website or by phone, we select a convenient time for your visit. We check the condition of the pads, discs, calipers, and brake fluid level.
request on WhatsApp
We offer original pads or analogues from trusted brands to fit your budget.
inspection and diagnosticsWe carefully remove the wheel and provide access to the brake mechanism.
estimate before work starts
We extract the old pads, clean the caliper, and install new ones, lubricating the guides.
work to factory procedureWe diagnose the operation of the calipers and, if necessary, replace the boots.
result check
We install the wheel back, bleed the brakes, and check the fluid level. We go out on the road, check braking efficiency and the absence of extraneous noises.
warranty in the work orderWalk-ins welcome. By appointment — no queue.
CARGID car repair team. 8–17 years of experience.
Author
Mobile auto electrician

Car alarm and car stereo installer

Auto electrician

Roadside assistance technician

Diagnostic technician

Engine mechanic (cylinder head repair)

Auto electrician and diagnostician

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

CARGID replaces Land Rover brake pads in Almaty as a full set per axle, with guide lubrication, a new wear sensor and brake bleeding. First comes diagnostics and a written estimate, and we start the repair only after you agree. The work is covered by a 6-month warranty, and we fix the timeline and terms in the work order. No waiting in line, daily 09:00–20:00.
Pads wear down gradually, and the owner notices it by the sound, the pedal and the light on the dash sooner than by mileage. Let's go through which sign tells you it's time for a replacement.
Metal-on-metal grinding, a longer pedal travel and a lit wear sensor light are three signals that the pads are almost gone and you shouldn't wait. Grinding means one thing — the friction lining has worn away and the caliper is rubbing its metal backing plate right against the disc: every kilometer in this mode takes hundredths of a millimeter off the disc and means the discs need replacing too, not just the pads. Longer pedal travel shows up when a pad has worn unevenly and the caliper needs more fluid to bring it against the disc. The wear sensor light comes on when the lining reaches the contact built into the sensor. If there's no wear sensor, go by the squeal during light braking at low speed — it appears before the grinding, and at that stage the replacement still doesn't touch the discs.
A squeal at low speed is usually the pad, pedal vibration when braking downhill is already about how the disc behaves, and a dull hum at speed points to a worn disc or bearing. The squeal comes from the edge of the lining when it wears down to the metal wear indicator: it starts touching the disc and makes a high-pitched tone. Pedal vibration signals that the disc thickness has dropped below the minimum allowed or the surface has developed wear, and the pad no longer makes full contact. A hum at 60–80 km/h is more often the wheel hub bearing than the brakes, so it's checked separately. Telling a pad from a disc by ear is only approximate — the exact answer comes from measuring disc thickness and inspecting the pads on the lift, which is why diagnostics come before the estimate, not after.
With us, pad replacement follows one route — from check-in and diagnostics to a test drive before handover. Below is what it looks like for the car owner, step by step.
The car is received by the service advisor, we run diagnostics on the brake system and issue a written estimate, and we start the repair only after you agree. The service advisor handles the work order from check-in to handover, so you discuss the scope of work and the parts with one person, not with different technicians at every stage. You choose the parts: OEM, aftermarket or your own — we install whichever option was agreed in the estimate. We take a photo report at key stages, show you the old parts and give them to you, and before handover we do a test drive — you see the scope of the replacement and how the car brakes. Land Rover brake pad replacement in Almaty with us fits into one visit: diagnostics, approval, the work and the road check run back to back, with no extra trips. In our experience, an estimate before the repair starts takes care of half the questions at handover — you see upfront what you're paying for.
Replacing brake pads isn't just about the parts themselves. Let's go through three things that determine how the car will brake after it leaves the shop.
We install all four pads on one axle at once, because different friction pulls the car to one side when braking. A fresh pad and an old one worn halfway down grip with different force: at 80 km/h you can feel that imbalance through the steering wheel and pedal. That's why the work order includes a full set of four pads per axle, not a separate pair. We also check the brake discs: when wear is below the limit, thin metal overheats and warps, and then it's cheaper to take pads and discs together as a set — no need to take the assembly apart twice. In my view, saving on one part turns into another visit a couple thousand kilometers later. If you put new pads on a worn disc, they bed in unevenly and the pedal kicks back — so when the disc measures below the limit, we suggest replacing the whole assembly, not piece by piece.
The old sensor stops working once the pads are removed, so we install a new one — it lights the warning in advance, and you have time to book before you hit metal. The Land Rover brake pad wear sensor sits on the axle together with the pads and wears down with them, so it isn't reused. The second item is brake fluid: it's hygroscopic and picks up moisture from the air over a couple of seasons. We change it every two years or when it darkens in the reservoir, and together with pad replacement we bleed the circuit so the pedal doesn't feel soft. We change brake fluid within an hour, pushing fresh fluid through the circuit under pressure and draining the old fluid from each caliper — moisture in old fluid boils, and that's exactly when the pedal sinks.
On a Land Rover, the rear axle pads are tied to the electronic parking brake, and the suspension and parts selection depend on the specific model. Here's what that means in practice when the car comes into the shop.
On Land Rover models with an electronic parking brake, the rear pads can only be replaced after switching the parking brake to service mode via a scanner — otherwise the mechanism won't retract. You can't push the piston in manually on these units: there's an electric motor inside that keeps the pad pressed against the disc. We connect to the diagnostic port, set the required algorithm, remove the parts, retract the piston, and reassemble the unit. That's why replacing pads on a Range Rover with an electronic parking brake always starts with proper diagnostics of the unit. We have dealer-level scanners for 40+ brands, so the procedure goes smoothly, and after the work the parking system is recalibrated — without that, it may not engage on the first press. If you come to a shop without such equipment, the technicians will either refuse the job or force the mechanism apart and bend it. In my opinion, saving on a scanner leads to repairing the entire unit.
| Model | What we consider when selecting | Replacement specifics |
|---|---|---|
| Range Rover Sport | Body weight, disc size | Rear — via scanner |
| Discovery | Axle load, mechanism type | We check the guide pins |
| Evoque | Compact unit, friction compound | Fronts are replaced more often |
| Freelander | Simple design | Mechanical parking brake on some versions |
After installing new pads, the owner is left with two questions — how the warranty works and how to drive for the first few kilometers. We answer with the facts we put in the documents when you pick up the car.
For Land Rover brake pad replacement, we provide a 6-month warranty; the term and conditions are recorded in the work order and the completion certificate when you pick up the car. The work order is handled by the service advisor — he also hands the documents to the owner along with the old parts, so you can see which parts were replaced. The warranty covers the work performed and the parts we installed, but not accidents after repair, third-party interference, or parts supplied by the client. If you bring your own parts, the work remains covered, but the part itself does not: quality claims must be made to the seller. Warranty diagnostics are free — bring the car in, we'll put it on the lift and see what happened.
We covered the main things that determine the result of brake pad replacement on Land Rover and Range Rover — from completeness to warranty. Below is a quick summary of key points to rely on when choosing a service and after repair.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost of replacing brake pads on a Land Rover at our service depends on the model and engine type. For most models (Discovery, Range Rover Sport, Evoque), the labor for replacing front pads costs from 12,000 tenge, rear — from 12,000 tenge. If replacement of pads with wear sensors is required, 3,500 tenge is added for each sensor. The final price depends on the complexity of access to the calipers and the condition of the guides. The exact cost can be quoted after diagnostics, which we perform free of charge.
On average, replacing brake pads on a Land Rover takes from 1.5 to 2.5 hours. This time includes removing the wheels, dismantling the calipers, replacing the pads, greasing the guides, and reinstalling the wheels. If additional replacement of discs or wear sensors is required, the time increases by 30-60 minutes. We always warn about possible delays in advance so you can plan your day.
Yes, we provide a warranty on all completed work — 6 months or 20,000 km, whichever comes first. The warranty covers the quality of installation: if the pads are installed incorrectly, we will fix the problem free of charge. The pads themselves are covered by the manufacturer's warranty, usually 6-12 months. We always record warranty obligations in the work order.
An appointment is advisable: pads for a specific Land Rover model are selected by VIN, and not all items are always in stock. If the kit is available, replacement takes from one to two hours depending on the model and condition of the brake system. If the pads need to be ordered, the timeframe is agreed separately.
Yes, you can bring your own brake pads. We will check their compatibility with your Land Rover model and their condition. It is important that the pads are of good quality and fit by size. If you don't have your own pads, we can select original or high-quality aftermarket ones. Installing your own parts does not affect the warranty on the work, but you assume responsibility for their quality.
If after replacing the pads you notice squeaking, vibration, or deterioration in braking, you should contact us immediately. During the warranty period, we will perform diagnostics and fix the problem free of charge. Most often, squeaking occurs due to improper bedding-in of new pads (initially, avoid sharp braking) or due to low-quality pads. In any case, don't delay your visit — it's a safety issue.
We offer standard pad replacement and extended. Standard replacement includes removing the calipers, replacing the pads, and greasing the guides. Extended — additionally cleaning and greasing the calipers, replacing wear sensors (if present), and checking the condition of the brake discs. Extended replacement costs 3,000-5,000 tenge more, but it increases the reliability of the brake system and prevents future problems. The choice depends on the condition of your car.
Yes, after replacing brake pads, it is recommended to perform bedding-in. During the first 200-300 km, avoid sharp braking and prolonged loads on the brakes. Try to decelerate smoothly so the pads and discs bed in to each other. Our mechanics also advise performing several emergency stops from 60-80 km/h to a complete stop in a safe place on the first day after replacement. This helps the pads adapt and improves braking efficiency.
Payment is accepted in cash and by bank card; non-cash payment by invoice is also possible for legal entities. The invoice includes the labor for replacing the pads and, upon agreement, the cost of the pads themselves. The price depends on the Land Rover model, the chosen pads, and the need for additional work, such as caliper servicing.
The main signs of brake pad wear: squeaking or squealing when braking, increased braking distance, vibration of the brake pedal, as well as an indicator on the dashboard (for models with wear sensors). Visually, you can check the pad thickness through the holes in the disc — if it is less than 3 mm, replace immediately. At a mileage of 30-40 thousand km on a Land Rover, it is recommended to check the condition of the pads at every maintenance. Our service offers free diagnostics of the brake system — we will check the wear and tell you if replacement is needed.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
Had the front pads replaced on a Discovery 4. Done in a day, price 145,000 tenge, as discussed. The car brakes more sharply now, the squeak is gone. Liked the service, the guys are competent.
On a Range Rover Sport, had the rear pads with a sensor replaced. The error on the dashboard is gone, brakes are excellent. Paid 98,000 tenge for labor and parts. Very satisfied, booked in advance, no problems.
Had the pads replaced on a Land Rover Evoque. There was a squeak when braking, after replacement it's gone. Cost 85,000 tenge, done quickly and with quality. Thank you!
Came in with a Discovery Sport with vibration when braking. Turned out the pads were worn out and the caliper was sticking. Replaced the pads and repaired the caliper, also bled the brakes. Everything is spot on, price 112,000 tenge, the car is like new.
Had the pads replaced on a Defender. Spent a long time looking for a service that doesn't push unnecessary work. Here they diagnosed quickly, said the rear pads still had life left, replaced only the front ones. Saved money. I recommend!
Range Rover Vogue, replaced the pads and caliper bushings, there was a knocking. Price 120,000 tenge, the work took 8 hours. The car now brakes as it should, no knocking. Pleasantly surprised that everything was explained in detail.
Urgently needed to replace the pads on an Evoque before a trip. They took me without an appointment, finished in 4 hours. The kit cost 90,000 tenge. No problems, everything is great.
Had the front pads replaced on a Disco 4. Everything went quickly, the car was handed over in a day. The quality of work is top-notch, price 150,000 tenge including discs. I recommend this service!
Had the pads replaced on a Range Rover Sport, everything went great. But what especially pleased me was that they checked the calipers and greased the guides, even though I didn't ask for it. A small thing, but nice. Price 100,000 tenge, term — 1 day. I will come back again.
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.