

Toyota Camry Headlight Polishing
- Cause
- Cloudy headlights due to plastic oxidation
- Found
- Severe cloudiness, microcracks on the surface
- Done
- Sanding, polishing, applying protective varnish

We restore your headlights' former clarity and brightness. We polish, adjust, replace glass and reflectors. We work with all types of headlights: halogen, xenon, LED. 12-month warranty on all types of work. Free diagnostics when repairing at our service center.
Headlight work: from polishing and adjustment to lens and glass replacement.

We remove haze and small scratches from the surface. The light becomes brighter, the look — cleaner.

We set the light beam using a device. The road is visible evenly, we don't blind oncoming drivers.

We restore broken tabs and mounting points. The headlight holds firmly again, without play.

We remove the old lens, install a new one and seal the joint. The headlight doesn't fog up and doesn't let water in.

We clean and restore the mirror layer of the reflector. The light is focused into a beam again, not scattered.

We remove the old headlight, install a new assembly and connect the connectors. Everything works as it should.

We replace worn lenses inside the headlight. The light beam becomes even and predictable.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
Real jobs are shown: the optical element with a defect and the result after repair.
The exact cost will be determined after diagnostics.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Polishing one headlight | 30–60 min | 12 mo | from 5 000 ₸ |
| Polishing two headlights | 1–2 hours | 12 mo | from 9 000 ₸ |
| Headlight beam adjustment | 30 min | 12 mo | from 3 000 ₸ |
| Headlight lens replacement (remove/install) | 1–2 hours | 12 mo | from 7 000 ₸ |
| Reflector restoration | 2–3 hours | 12 mo | from 12 000 ₸ |
| Headlight assembly replacement | 1–2 hours | 12 mo | from 2 000 ₸ |
| Headlight lens replacement | 2–4 hours | 12 mo | from 15 000 ₸ |
| Headlight lacquer coating | 1 hour | 12 mo | from 5 000 ₸ |
| Condensation removal | 1–2 hours | 12 mo | from 4 000 ₸ |
| Headlight mounting repair | 1–2 hours | 12 mo | from 4 000 ₸ |
| Bulb replacement (excluding bulb cost) | 30 min | 12 mo | from 1 500 ₸ |
| Optics diagnostics | 30 min | 12 mo | Free |
Lens and reflector replacement work requires headlight disassembly. Materials are not included in the price. Diagnostics are free when repairs are done at our service center. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
First we remove scratches with 1500 abrasive, then 3000, then with paste on felt. The lens doesn't become hazy or yellow.
We heat the housing with a construction dryer to 80°C, the sealant softens, we remove the lens without chips and cracks.
Polishing and lens replacement — 3–4 hours, reflector restoration — up to 6. Brought in the morning — picked up in the evening.
If the lacquer starts to peel off or the mount comes loose — we'll redo it for free. We cover exactly these defects.
We perform diagnostics, repair and polishing of headlights with a guaranteed result.

You leave a request or call, we clarify the symptoms and schedule a convenient time. We assess the condition of the headlights, determine the cause of the problem and calculate the cost.
request on WhatsApp
We give the exact price and terms, after your approval we start the repair.
inspection and diagnosticsWe carefully remove the headlights, disassemble, clean and prepare the surfaces.
estimate before work starts
We fix cracks, chips, replace the lens, reflector or ignition unit.
work to factory procedureWe seal the seams, assemble the headlights and check the fit.
result check
We adjust the tilt angle and direction of the light beam on the stand. We install the headlights, check the operation in the presence of the client and provide a warranty.
warranty in the work orderWalk-ins welcome. By appointment — no queue.
CARGID car repair team. 8–17 years of experience.
Author
Mobile auto electrician

Car alarm and car stereo installer

Auto electrician

Roadside assistance technician

Diagnostic technician

Engine mechanic (cylinder head repair)

Auto electrician and diagnostician

Send a photo of the damage, the car make and year to WhatsApp. We will give you a price range, the timeframe and help you pick a booking time.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

CARGID is a full-service auto shop in Almaty at Mukagali Makataeva, 129. We start headlight repair with an optics diagnostic and a written estimate, and a service advisor manages the work until the car is handed over. We polish in 3 stages, replace glass and restore the reflector within 1 day, and provide a 12-month warranty on headlight work with the terms recorded in the work order.
Headlights get cloudy, fog up, and crack for various reasons, and the cause determines what to do — polish, replace the glass, or disassemble the housing. Let's go through the signs one by one.
Polishing removes the haze from the top layer of the glass, restoration brings back the light output of the reflector and lens, and glass replacement is needed for cracks and chips that break the seal. External treatment removes the oxidized layer, eliminates the fine network of scratches, and restores the clarity of the lens. Reflector restoration is work on the inner surface: the deposited layer darkens from moisture and overheating, the light comes out in patches, and polishing won't fix that. Glass replacement is required for mechanical damage to the lens — a crack, chip, or a seam that has come apart. The decisive sign is not the appearance but the depth of the damage: if a fingernail catches on the crack, polishing won't help, and the lens needs to be replaced. We start with that assessment: the technician checks the depth of the damage and only then suggests polishing, glass replacement, or reflector restoration.
Condensation in a headlight is almost always a loss of housing seal: a crack in the glass, worn sealant along the seam, or a loose fit after a previous repair. We list condensation removal as a separate line item in the price list: we remove the headlight, find the leak point, seal the seam with heat-resistant sealant, and check the fit. Natural ventilation causes light misting along the edge that clears within 10–15 minutes after the lights are turned on; if droplets persist or collect at the bottom, that's a seal failure and you shouldn't delay: moisture eats away the reflector. Most often the leak is along the top seam, where the housing heats up the most — that's where the sealant ages first. Before sealing, the technician also checks the drain valves: a clogged valve creates a pressure difference, and the seam comes apart again.
A crack in the headlight glass lets moisture and dirt into the housing, the reflector gradually darkens and loses light output, and the lens itself can shatter from vibration or temperature changes. Through an open chip, road dust and chemicals get inside, settle on the reflective layer and the lens, and the light starts to hit unevenly — oncoming cars get dazzled, and the driver loses the illuminated area on the shoulder. On top of that, water in the housing accelerates corrosion of contacts and connectors, and in a couple of months a lamp or leveling motor failure adds to the crack. The sooner you replace the glass, the cheaper the job: while the reflector is intact, it's limited to replacing the lens, but a neglected case already requires reflector restoration.
The technology depends on what exactly is damaged. Here's how polishing, housing disassembly, and reflector restoration are done, and which jobs suit which task.
We work in 3 stages: first we remove scratches with P1500 abrasive, then P3000, and finally with paste on a felt wheel. The glass doesn't get cloudy or yellow, and a protective clear coat with UV protection extends the result. In our practice, polishing always goes together with clear coating — otherwise the plastic gets cloudy again under the sun within a few months. The technician removes the headlight, works on the lens surface without digging into the edges, washes the surface, and dries it before applying the compound. The clear coat is not cosmetic but protection from UV, which triggers the re-clouding; without it, a polished lens returns to its original state noticeably faster. We apply two thin layers with intermediate drying — that way the coating lays evenly and doesn't run.
During disassembly, we heat the housing with a heat gun to 80 °C — the seam compound softens, and the glass comes off without chips or cracks. After replacing the lens, we apply heat-resistant sealant along the seam and check the fit, so the headlight doesn't fog up again after glass replacement. Heating goes around the perimeter of the housing, not the center — that way the seam compound comes off evenly along the entire length. We remove the remnants of the old layer completely, otherwise the new one won't lay flat and the joint will start letting moisture through. It's the housing that needs heating, not the glass: local overheating of the lens leads to microcracks that show up later, after assembly. Before installation, we check the fit dry — if the gap is uneven, the seam will have to be redone.
| Job | When it's needed | What we do |
|---|---|---|
| Headlight polishing | Cloudiness, yellowing, fine scratches | 3 stages P1500 → P3000 → paste, then clear coat |
| Headlight glass replacement | Cracks, chips, seal failure | Heat housing to 80 °C, remove, new lens, sealant |
| Reflector restoration | Dim light, darkened reflector | Disassembly, new reflective layer, reassembly |
| Headlight lens replacement | Uneven beam, cloudy lens | Disassembly, lens replacement, adjustment on the stand |
| Condensation removal | Persistent droplets inside | Find the leak, seal the seam, check the fit |
| Headlight mount repair | Broken tabs, loose fit | Restore mounting points, install |
| Headlight assembly replacement | Housing destroyed, repair not feasible | Remove old, install new, adjust |
The time depends on the operation, not the car make. Here's how long each job takes and how the visit works from booking to handover.
Polishing and replacing the headlight lens takes 3–4 hours, and restoring the reflector takes up to 6 hours. Drop it off in the morning and pick it up in the evening — we do all the work in 1 day. We polish in three stages: we remove scratches with P1500 abrasive, then P3000, then with paste on felt, so the lens doesn't get cloudy or yellow. When disassembling, we heat the housing with a heat gun to 80°C — the sealant softens, and we remove the lens without chips or cracks. Treating two headlights and applying the clear coat fit into the same business day, while replacing lenses or a complete headlight assembly takes more time for disassembly and beam adjustment. The exact time depends on the condition of the mounts and sealant: if a cracked mounting tab is found during disassembly, headlight mount repair is added, and we tell you about it before work begins.
The service advisor takes in the car and manages the work order through to pickup. First we do an optics diagnosis and a written estimate, and we start work only after the client agrees. We take photo reports at key stages, and we show you the old parts and hand them over so you can see what was replaced. Before pickup we do a test drive. It's worth booking ahead if you plan to come at lunch or in the evening: with an appointment the car is taken without waiting in line, and the work takes half a day. We're open daily from 09:00 to 20:00, seven days a week — so you can make it before or after work. The service advisor usually handles condensation removal and headlight adjustment in the same visit; no separate appointment is needed for these.
Yes, it's the client's choice: OEM, aftermarket, or your own lens and lenses. We install the client's part, but the warranty doesn't cover it — only the work performed, with the term and conditions recorded in the work order. If you bring your own lens, have its geometry and mounting points checked: if the lens doesn't fit the housing, we can't guarantee the seam is sealed, and condensation will come back inside the headlight. Same logic for lenses — the mounting diameter and fasteners must match the housing, otherwise the beam points off to the side and adjustment won't help. In our experience, client parts are most often installed on older cars where the right OEM part can no longer be found — so we check the geometry before disassembly to avoid wasting time on a lens that clearly won't fit.
A warranty isn't a line in an ad — it's terms written into the documents. Here's exactly what we cover, for how long, and which cases fall outside our obligations.
We give a 12-month warranty on headlight work. The terms and period are recorded in the work order and the completion certificate when you pick up the car, and diagnosis for a warranty case is free. We do headlight repair in Almaty with the same responsibility: polishing, lens replacement, reflector restoration, and clear coat application are covered by this period just like lens replacement and condensation removal. The obligations apply to the work performed and the parts we install — that is, to what depends on the technician, not on outside factors. We take photo reports at key stages of the work to record the original condition of the housing and mounts. In my view, an honest period matters more than a loud promise: over 12 months you can see whether the sealant holds the seam and whether the clear coat gets cloudy after polishing.
The warranty doesn't cover accidents after repair, tampering by third parties, normal wear of consumables, or a part brought by the client. These are standard boundaries: they cover cases where the result doesn't depend on our work. If the owner brought their own bulb or lens, the supplier — not the technician — is responsible for its quality and compatibility with the housing. Normal wear is also outside our obligations — the clear coat wears away over time from road debris, and that's normal use, not a defect. If the headlight fogs up again after the work, the cause is usually a seam that wasn't sealed during a previous repair — that's why we record the housing condition in a photo report before work begins. That photo later helps tell our mistake apart from someone else's.
Come to the shop, we do a free diagnosis for a warranty case, find the cause, and fix it under our obligations if it's a warranty case. We're open daily 09:00–20:00, seven days a week, by appointment — no waiting in line. The service advisor opens the work order and manages it through to pickup, so the service history doesn't get lost between shifts. If the cause isn't covered — for example, the headlight was damaged on a trip — we'll show you in the photo report and offer a separate estimate. Keep the work order and certificate: these documents determine a warranty case, and without them it's harder to restore the terms. In our experience, we try to close headlight issues the same day the owner comes in with the paperwork.
Halogen, xenon, and LED behave differently during disassembly and restoration. Here's what changes in the work and what the owner should watch for.
Halogen headlights are most often polished and get their lens replaced, xenon ones with auto-leveling need calibration after disassembly, and LED headlights are polished the same as halogen, but disassembly is harder because of the electronics inside the housing. Halogen has a simple design: reflector, incandescent bulb, lens on sealant — reflector restoration and lens replacement go predictably. A xenon headlight with auto-leveling is more complex: the ballast, body position sensors, and leveling mechanism are interconnected, and after disassembly the beam has to be set again. LED lighting inside the housing carries a driver board and a cooling heatsink, so it's important not to overheat the electronics during disassembly. The LED module must not be overheated during disassembly — heating the housing with a heat gun to 80 °C is safe for the sealant but requires care near the driver board.
Yes, after disassembling a xenon headlight with auto-leveling and after replacing lenses, we adjust the beam on a stand — otherwise the light points off to the side or up and blinds oncoming drivers, and the adjustment is part of the final check before pickup. We replace lenses in the headlight with a subsequent check of the cutoff line on the headlight adjustment stand: even a shift of a couple of degrees changes the road lighting zone. Auto-leveling is calibrated to the marks on the housing, and if the marks are off during disassembly, the beam will be off even with correct assembly — that's why we record the marks before disassembly. In our experience, on xenon and projector lighting, adjustment after assembly is mandatory, not optional: the minutes saved on it come back as a repeat visit.
Let's wrap up on lighting: we've put together the key guidelines that help you choose between polishing, restoration, and replacement, and understand what the warranty covers after a visit to the shop.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe price of headlight repair in Almaty depends on the type of damage and the car brand. Headlight polishing costs from 5,000 tenge per headlight. Replacement of the lens (glass) — from 25,000 to 60,000 depending on the model. Restoration of mounts — from 7,000 to 15,000 tenge. The price is affected by the complexity of disassembling/assembling the headlight, the need to remove the bumper, and the cost of consumables. Our technicians will inspect the headlight for free and give the exact cost before starting work. Exact prices are in the price list on this page.
The repair time depends on the complexity. Simple polishing takes from 30 to 60 minutes. Repair of a small crack — 1–2 hours. Repair of mounts or sealing — from 2 to 3 hours. Replacing the glass with sealing takes 3–5 hours. If the headlight was removed and disassembled, we add time for disassembly and assembly. Usually the repair takes from one hour to one day. In each case, we give the exact time after diagnostics.
Yes, we provide a warranty for all types of headlight repair. For polishing and polishing with a protective coating — 6 months. For crack repair, sealing, and restoration of mounts — 12 months. For replacement of the lens with sealant — 12 months. If a defect appears during the warranty period (for example, condensation inside or a crack at the repair site), we will fix the problem free of charge. The warranty does not cover mechanical damage after repair (accident, stone impact).
It is better to make an appointment in advance so you do not have to wait. Our slots are often fully booked, especially on weekends. Call +7 775 711 58 26 or leave a request on the website — we will find a convenient time. If you come without an appointment, we try to accommodate you, but there may be a queue. Some services have same-day slots, so if it is urgent — call us, and we will check available windows. Diagnostics is free, and you can come on any working day from 9:00 to 20:00.
Yes, you can bring your own materials, for example, sealant, glass, or polish. But we are not responsible for their quality and do not provide a warranty for such materials. If you use your own parts, the warranty on the work remains, but not on the material. We recommend using proven materials that we have: they are selected for specific types of headlights and will ensure a long-lasting result. In most cases, our materials are better in terms of price/quality.
We guarantee the quality of every repair. If after repair you find a defect: condensation inside the headlight, glass peeling off, a crack at the repair site, or polishing marks — we will fix the issues free of charge. All work goes through multi-stage checks: leak testing, checking the correctness of the light, and uniformity of polishing. If problems arise during the warranty period (12 months), just call us — we will schedule a convenient time, and the technician will fix the situation without additional payment.
Polishing removes cloudiness, scratches, and yellowness from the headlight surface, restoring clarity. Crack and chip repair — eliminating mechanical damage that disrupts the seal or integrity of the headlight. Glass replacement is required for severe cracks or chips when it is impossible to restore the seal. Polishing solves only cosmetic problems. If there is a crack remaining on the glass, the headlight must be sealed or the glass replaced. After inspection, the technician will recommend the optimal option that will last a long time.
After headlight repair, it is important to care for them properly. Do not wash the headlights with aggressive chemicals and do not use abrasive sponges. Wash with plain water and a soft cloth or sponge. Avoid getting tar spots or resin on the headlights — they should be removed immediately. Do not use solvents. After polishing, we apply a protective coating (polymer or lacquer), which extends the effect. It is recommended to renew the protective coating about once every 6-12 months. Do not use store-bought headlight restorers — they can damage the protective layer. If you notice condensation inside the headlight, contact us free of charge.
Payment is possible in cash, by bank card (Visa, MasterCard, Homebank, Kaspi), and via QR code (Kaspi Pay). We issue a cash receipt and warranty card. Non-cash payment is also available for legal entities (invoice, contract). When paying by card for services over 30,000 tenge, no commission is charged. Partial prepayment is possible if materials are needed. All prices include VAT. Payment is made after the work is completed and the result is checked.
If access to the headlight is difficult (for example, the bumper needs to be removed), we remove the headlight. Sometimes polishing can be done without removal if the damage is on the surface. Removing the headlight affects the cost: additional work to remove/install the bumper may cost from 2,000 to 5,000 tenge. But this ensures quality repair without damaging the body. We remove the headlight for repair of internal mounts, glass replacement, or sealing. Usually we first perform diagnostics, and the technician reports whether the headlight needs to be removed and what the preliminary price will be.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
The headlights on a Mazda CX-5 were fogging up, and the light became dim. The guys did polishing and sealing. It turned out great, no fogging after a month. The price was 20,000 tenge, and it took one day. I recommend.
A stone broke the headlight glass on a Honda CR-V. They replaced the glass, and also polished and cleaned it. Clear, bright light, everything is dry. I am grateful for the work, 45,000, two days.
I came in with a complaint about dim light on a Toyota Camry. It turned out that the contacts in the connector had oxidized. They fixed it quickly, replaced the connector, and the light became like new. 12 thousand, an hour of work. Everything was spot on.
On a BMW X5, one headlight would not turn on. Diagnostics showed the ballast had died. They replaced it for 28 thousand, two days. They work great, the technicians know their craft.
After an accident on a Lexus RX350, the headlights became cloudy and had chips. They did polishing and restored the glass. The light became brighter, the headlight is clear. Thank you, 30 thousand, 1 day.
Kia Sportage, one headlight did not work at all. I thought it was the bulb, but it turned out to be the ballast. They replaced it at CARGID. Now everything works, there is plenty of light. 28,000, repaired in two days. Thank you!
On a Toyota Camry, the headlights turned very yellow. Polishing gave an excellent result, they became like new. Plus they applied a protective coating. 25,000 tenge, done in a day. I recommend.
Replacing the trim on an Audi A6, there was a crack. Did everything cleverly, after a week no moisture gets in. Precise, quality, price 45k, two days. Thanks!
After suspension repair on a Hyundai Tucson, I noticed the headlights fogging up. They did sealing, now everything is dry. 18,000, one day. Seems simple, but important. Almaty, Tole bi St., near the metro. I liked it. I recommend!
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.