

Crossover was pulling to the right
- Cause
- After hitting a pothole, the car constantly pulled to the right
- Found
- Right wheel camber off by 1.5 degrees
- Done
- Camber and toe adjustment on a 3D stand

Correct wheel alignment is the key to safety and savings. We perform diagnostics and adjustment of wheel alignment angles on a modern 3D stand. Accuracy up to 0.01 degrees and 6-month work warranty. Book a wheel alignment and feel the difference in handling.
We adjust wheel alignment angles for your suspension and after repairs

We adjust the angles at the specified suspension height. The client gets a smooth ride and predictable handling on the road.

We adjust the angles for modified stiffness and ride height. The client gets stability in corners and less tire wear.

We set the camber angle of the front wheels to factory specifications. The client gets a straight steering wheel and even tire wear.

We correct the front wheel toe. The client gets stable straight-line driving without pulling to the side.

We adjust the rear multi-link suspension for both angles. The client gets even tire wear and predictable rear behavior in corners.

We adjust camber and toe front and rear. The client gets fully configured alignment to factory parameters.

We check and set the angles after replacing tie rod ends or tie rods. The client gets a straight steering wheel and correct tire wear.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
Real cases from our practice: cause, diagnosis and result.
Precise adjustment of wheel alignment angles for your vehicle.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Alignment diagnostics (passenger car) | 30–40 min | 6 mo | from 5 000 ₸ |
| Alignment diagnostics (SUV / crossover) | 40–60 min | 6 mo | from 7 000 ₸ |
| Front axle camber adjustment (passenger car) | 1 hour | 6 mo | from 10 000 ₸ |
| Front axle toe adjustment (passenger car) | 1 hour | 6 mo | from 10 000 ₸ |
| Front axle camber and toe adjustment (passenger car) | 1–1.5 hours | 6 mo | from 14 000 ₸ |
| Rear axle camber and toe adjustment (multi-link suspension) | 1.5–2 hours | 6 mo | from 17 000 ₸ |
| Camber and toe adjustment for both axles (full alignment, passenger car) | 2–2.5 hours | 6 mo | from 21 000 ₸ |
| Wheel alignment adjustment on SUV / crossover | 2–3 hours | 6 mo | from 25 000 ₸ |
| Alignment after replacing tie rod ends / tie rods | 1–1.5 hours | 6 mo | from 12 500 ₸ |
| Alignment after replacing bushings / control arms | 1–1.5 hours | 6 mo | from 14 000 ₸ |
| Alignment after replacing shock absorbers / springs | 1.5–2 hours | 6 mo | from 15 500 ₸ |
| Alignment after suspension lift / ride height change | 2–3 hours | 6 mo | from 19 500 ₸ |
| Alignment for vehicles with air suspension (height adjustment) | 1–2 hours | 6 mo | from 16 000 ₸ |
| Express alignment (within 1.5 hours, appointment by phone) | 1–2 hours | 6 mo | from 18 000 ₸ |
| Mobile alignment (at customer's location, Almaty) | 2–3 hours | 6 mo | from 25 000 ₸ |
| Computer alignment diagnostics with printout of parameters | 30–40 min | 6 mo | from 5 000 ₸ |
| Additional adjustment for non-standard wheel offset / tire width | 1–1.5 hours | 6 mo | from 12 000 ₸ |
| Alignment for vehicles with modified suspension stiffness (sport / tuning) | 2 hours | 6 mo | from 20 000 ₸ |
| Full alignment for minivans / commercial vehicles | 2–3 hours | 6 mo | from 22 000 ₸ |
The exact cost depends on the make/model of the vehicle and the condition of the suspension. Before adjustment, a mandatory inspection of the chassis is performed. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
We read the angles with a 3D stand using targets: error of 1–2 minutes. Rulers and levels do not provide such accuracy.
Before adjustment, we listen for play in joints, bushings, tie rods, and hubs. A worn component does not hold the angle — adjustment is pointless.
After replacing tie rods, control arms, or springs, the camber changes immediately. We set and fix it in an hour, with a printout of angles before and after.
If the camber changed without an impact or repair — come back, we will readjust for free. We provide the stand printout.
We show how we restore straight-line stability and responsiveness to your car — in a single visit.

You call or leave a request on the website, we find a convenient time. Booking takes a couple of minutes. We accept the car, clarify symptoms: pulling to the side, rapid tire wear, steering knock. We perform an initial inspection.
request on WhatsApp
We always check bushings, ball joints, tie rod ends, tie rods. Play is not allowed — the angles will not hold.
inspection and diagnosticsWe drive the car onto the 3D stand, secure it, and install targets. The computer shows the current angles with all deviations.
estimate before work starts
We compare the readings with the manufacturer's parameters. We find deviations in camber, toe, caster, and identify the cause.
work to factory procedureWe loosen the fasteners, rotating eccentrics or threaded rods, and bring the angles to ideal. We monitor every movement on the screen.
result check
We perform a repeated measurement in motion and statically. We make sure all parameters are in the green zone and reset errors if any. We print a before-and-after report, hand over the keys and advise the next check in 10-15 thousand km. Payment upon completion.
warranty in the work orderWalk-ins welcome. By appointment — no queue.

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

CARGID in Almaty does wheel alignment on a 3D stand with 1–2 minute accuracy. First we check for play at four suspension points, then set the angles and give you a before-and-after printout. The work is covered by a 6-month warranty, and we put the timeframe in the work order.
Camber, toe and caster are separate suspension parameters, while wheel alignment is the general term that covers them all. We break down each angle so you know exactly what you're ordering on the stand.
We treat "camber-toe" as the everyday name and a full measurement of all three angles on both axles with a printout as its technical essence. In practice this means adjusting camber and toe on both axles: first we set the front camber, then the front toe, then both parameters at the rear. We take on separate jobs — front camber or toe only — when the design doesn't allow rear axle adjustment or the client came in after a targeted suspension repair. On the 3D stand in our shop the technician sees all four wheels at once and checks each value against the factory spec for your model. If a shop calls only toe its service, the rear axle and caster stay out of control, and the pull comes back within a few thousand kilometers — ask for a printout of all angles before and after. Wheel alignment in Almaty is the same procedure with a full measurement of all angles, and we perform it on a 3D stand with a before-and-after printout.
On a rear beam the camber is not adjustable; on a multi-link suspension both camber and toe of the rear axle are adjustable. A beam is a rigid part: its angles are set at the factory and there's nothing to change them with, so the technician only works with rear toe within the play of the mounts. A multi-link setup has adjustment eccentrics and arms: both parameters are set here, and a full measurement of all four wheels makes sense. The front axle on most passenger cars is adjustable for camber and toe, but on some designs the front camber is fixed too — then it is only measured. That's why on a beam the technician first checks the body geometry and the condition of the beam itself, and only then decides what can actually be set: a bent beam or sagging bushings won't hold an angle under any adjustment.
Most often people come to us with a pull to one side, an off-center steering wheel or uneven tire wear. But not every pull is fixed by angles — some cases come down to tires, brakes or the steering rack.
We recommend checking the angles every 10–15 thousand km, at the seasonal tire change and after any pothole hit at speed. Factory tolerances are designed for smooth pavement, not the realities of a big city: on winding roads and elevation changes the load on the suspension is higher than on the highway, and the values drift faster. The seasonal tire change is a convenient reason to combine the swap with a measurement: we'll check the play and pressure at the same time. Our 3D stand reads the parameters from targets with an accuracy of 1–2 minutes, so a deviation shows up before it becomes noticeable through the steering wheel. The mileage schedule only works for calm driving — with frequent trips over broken streets, check more often than once a year, otherwise uneven tire wear will cost more than the alignment itself.
A pull can come from tire conicity, a sticking caliper or play in the steering rack, and then alignment won't fix the problem. Conicity comes from improper tire storage or cord wear — the wheel rolls along an arc even with perfect angles. A sticking caliper drags one wheel, and the car pulls toward it. Play in the rack or tie rod ends causes wandering that the stand won't fix. That's why we check the tires and brakes first and only run the stand if the cause really is the angles; otherwise the client pays for work with no result. Before adjustment we listen for play at four points — joints, bushings, tie rods and hubs: a worn component won't hold an angle, and the set value drifts within a few kilometers.
We walk through the whole sequence from drop-off to pickup: what the technician checks before the stand, how the readings are taken, and what you get to keep. That way it's clear what you're paying for and why you can't just dial in the numbers.
We read the angles with a 3D alignment rig using targets, accurate to within 1–2 minutes of arc, which rulers and levels simply can't match. The targets mount on the wheels, cameras track their position, and the system builds a spatial model of the axles, showing camber, toe and caster for each axle separately. The technician rolls the car and turns the steering wheel as the rig prompts to compensate for wheel runout. The measurement takes a few minutes per axle and doesn't require taking the suspension apart. That's why 3D wheel alignment on a rig gives consistent results that don't depend on how sharp the technician's eye is. Heavy uneven tire wear can throw the reading off, so we warn the customer in advance and suggest sorting out the tires first. In my view, accuracy measured in minutes matters more than speed: half a degree of difference on the front axle already makes the car pull noticeably at highway speeds.
Angle setup depends on the suspension design: some cars allow both axles to be adjusted, others don't touch the rear camber at all. We lay out the differences in a table so the owner can see right away what's actually adjustable on their car.
| Suspension type | What's adjustable | Measurement nuance |
|---|---|---|
| Rear beam axle | Rear toe | Camber is not adjustable |
| Multi-link | Camber and toe on both axles | More adjustment points |
| Air suspension | Both axles by ride height | Measured at operating height |
| Sport suspension | Both axles for the modified ride height | Tolerances are not factory |
We set the angles for air suspension and sport suspension to the actual ride height, not the factory one. With air suspension the car holds several ride-height modes, and each gives a different arm position, so we measure in the mode the car is driven in most often. On sport suspension with a lowered stance or shortened springs, the factory tolerances don't fit either: the wheel angle shifts along with the body's position relative to the road. We measure both axles, compare against the actual ride height, and set to it. With air suspension it's important to catch the operating height — otherwise the angles drift when the mode changes and the steering wheel ends up crooked again. So before pulling onto the stand, tell the technician which mode you drive in on weekdays — that determines the height the parameters are set to.
We cover two related scenarios — what to do after replacing suspension parts, and where to look if the pull remains even after alignment on the stand.
For warranty cases, we do the diagnostics free of charge and tell you honestly if the cause isn't the angles but tire conicity, a sticking brake caliper, or play in the steering rack. First we check the pressure and rotate the wheels — that's exactly how conicity shows up. Then we look at the brake system: a sticking caliper piston pulls the car to one side no matter how the angles are set. Next is the steering: play in the rack or a tie rod end won't let the angle hold, and the adjustment won't last long. The warranty on the work is 6 months, and we write the term and conditions into the work order. The warranty doesn't cover accidents or third-party interference, but if the angles drift because of our work, we redo it at our own expense. We recommend coming back for a check after 1–2 thousand km — new parts settle in, and the angles can be corrected before the tires suffer. That visit takes a few minutes and doesn't need an appointment.
We've put the essentials for your visit in one place: warranty terms, how the estimate works, how long the job takes, and booking. That way you know what to expect from the shop before you even arrive.
We give a 6-month warranty on wheel alignment and write the term and conditions into the work order and the completion certificate when you pick up the car. You keep the document, so if you ever have a question about the angles, you don't need to remember the date of your visit — just show the certificate to the service advisor. We also attach a copy of the estimate to the work order. The warranty covers the work performed and the parts installed. It does not cover accidents, third-party interference, or normal wear of consumables. One more thing about a part the customer brings in: it isn't covered by the warranty, since we didn't check its condition before installation. If there's ever a reason to check, diagnostics for a warranty case are free — in my view, that's fairer than charging for a second look at our own work.
A quick summary of this section: what full geometry is, when to come to the stand, and which documents to check when you pick up the car.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost of wheel alignment at CARGID is from 14,000 to 25,000 tenge. The price depends on the type of suspension and the complexity of adjustment. For most passenger cars with independent suspension (MacPherson), the service costs from 14,000 tenge. If the car has a multi-link or rear multi-link suspension, the price may be higher — up to 17,000 tenge. For SUVs and commercial vehicles with dependent suspension (beam, leaf springs), the price reaches 25,000 tenge, as more time and special tools are required. The cost is also affected by the condition of the adjusting bolts — if they are seized and require replacement, this is considered separately. We always state the exact price before starting work after diagnostics on the stand.
On average, the wheel alignment procedure takes from 40 minutes to 1.5 hours. This depends on the condition of the suspension and the accessibility of the adjusting elements. If the adjusting bolts yield easily, we finish in 40-50 minutes. If they are seized, replacement or heating is required, and the time increases to 1.5 hours. Please note that we only do geometry on a serviceable suspension — if there is play, worn bushings, or bent arms, these problems must be fixed first, otherwise the adjustment will be ineffective. Therefore, before geometry, the master may perform a preliminary suspension diagnostics.
Yes, we provide a warranty on the performed wheel geometry work. It is valid for 6 months or 10,000 km (whichever comes first). The warranty covers the absence of errors in adjustment and the correctness of the set angles. If during the warranty period you notice that the car pulls to the side or the tires wear unevenly, we will re-diagnose for free and, if necessary, correct the angles. However, the warranty does not cover cases where you hit a pothole, had an accident, or the suspension was modified (e.g., spacers, springs installed without our involvement). It is also important that the tire pressure is normal.
We recommend booking in advance, especially on weekday afternoons and weekends. You can book by phone or via WhatsApp, choosing a convenient time. This guarantees the stand will be free and you won't have to wait. However, if you can't book — you can come without an appointment, and if there's a slot, we'll take you. The waiting time usually does not exceed 30-40 minutes. To avoid unpleasant surprises, it's better to call and check for available slots. Also, let us know if you have special features — for example, low clearance or large wheels that may require a special approach.
As part of the 'Wheel Geometry' service, we do not use consumables other than penetrating lubricant for bolts. Sometimes adjusting bolts or shims are required. If you want to install your own bolts, it is possible, but we must make sure they fit in size and quality — otherwise they may not provide correct adjustment or may quickly fail. If we need bolts, we use our own — they are in stock for most brands. If you need work on replacing arms, struts, bushings — these are other services, and you can provide the parts, but we are responsible only for installation, and you are responsible for the quality of the parts. In the case of geometry, it's easier to use our stand and our diagnostics.
If after performing geometry you have problems — the car pulls to the side, the steering wheel is crooked, or the tires wear quickly — you must return to us immediately. During the warranty period, we will re-diagnose for free. Keep in mind that the cause may not be the wheel alignment angles, but other malfunctions: uneven tire wear (e.g., a crooked tire, conicity), brake mechanisms, steering malfunction, suspension play. Therefore, we will first check if the angles on the stand are correct, and then evaluate other aspects. If our error is found — we will fix it at our expense. If the cause is different, we will honestly tell you about it and offer a solution.
Often these terms are used as synonyms, but there is a nuance. Wheel alignment is the adjustment of wheel installation angles: camber (the tilt of the wheel relative to the vertical) and toe (the angle between the wheel's plane of rotation and the vehicle's longitudinal axis). This is a standard procedure on a 3D stand. Full geometry may include caster adjustment (longitudinal tilt of the steering axis) and other parameters, if provided by the vehicle design (e.g., on multi-link suspensions). Also, full geometry includes checking and adjusting the rear axle, if it is adjustable. We always perform full geometry: we check all angles provided by the manufacturer for your car and adjust everything that can be adjusted without replacing parts.
After wheel geometry adjustment, it is important to follow several rules so that the result lasts as long as possible. 1) For the first 200-500 km, try to avoid sudden braking and driving over deep potholes. 2) Regularly check tire pressure and keep it normal — incorrect pressure distorts the angles. 3) Do not overload the car beyond the factory norm. 4) After 1000-2000 km, we recommend coming for a control check of the angles — we do this for free within 30 days after the initial adjustment. 5) If you notice that you bought new tires or changed the suspension — geometry must be repeated. 6) Try not to hit curbs and not to park with wheels in potholes — this disrupts the angles.
You can pay in any convenient way: cash, bank card (Visa, MasterCard) via POS terminal, or transfer to our account (Kaspi, etc.). We work with legal entities — we provide an invoice. For individuals, payment after the work is done. You can pay both at the service cash desk and online via transfer. When ordering a service through the website, you can make a prepayment, but it is not mandatory. We issue a receipt and a cash receipt (when paying by card). There is also a cumulative discount system for regular customers — a 5% discount on repeat visits. Ask the administrator for details.
It is recommended to check geometry every 10,000 - 15,000 km or once a year, or after any repair work related to the suspension. Signs that the angles are off: the car pulls to the side when driving straight, you have to hold the steering wheel at an angle, uneven tire wear (e.g., worn edges or center), vibration or instability at speed, squeaking or crunching in turns (may be caused by other reasons, but geometry can also be a cause). Also be sure to do geometry after replacing arms, struts, tie rods, ends, ball joints, springs, as well as after installing new rims or tires. If you hit a pothole at high speed — it's better to check.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
I have a Toyota Camry, after a broken road the steering wheel became crooked and the car was pulling. On my brother's advice, I booked at CARGID. They did the wheel alignment on the stand and also tightened all the mounts. I paid 12,000 tenge, it took less than an hour. The car became like new — the steering wheel is straight, no pulling. Thanks for the work and politeness!
I brought my Kia Sportage, the tires were wearing on the edges. I thought it was the tires, but it turned out the camber was off. The guys at CARGID adjusted everything, showed me on the screen before and after. I paid 9,500 tenge, and after a month I see the result — the wear became even. Now I'll only go here.
I was driving in the north, hit a pothole, and after that the car was being thrown from side to side. I came to CARGID, they checked the suspension, and it turned out the tie rod end was bent. They replaced it and adjusted the geometry. It cost 18,000 tenge including the part. Now everything is perfect, I recommend it!
My Hyundai Tucson started 'floating' on the road, especially on the highway. I stopped by CARGID, the master explained that the caster was incorrect. They selected shims and adjusted it. It cost 8,000 tenge. After the repair, the car drives straight, the steering wheel returns by itself. Excellent service, everything is fair.
Had to fix suspension on my Mazda 6, after some road work the steering felt vague. Brought it to CARGID, they did a 3D alignment and found the toe was off. Adjusted everything, car drives straight now. Cost me only 10,000 tenge, took about 40 minutes. Highly recommended!
A couple of months ago I noticed that the front tires were wearing on the inside. I booked at CARGID, it turned out the toe was off. The specialists adjusted everything on the stand and gave me a printout with the parameters. I paid 13,500 tenge, but now the tires aren't being eaten up. Good thing it was in time.
After replacing the springs, I had to do the geometry. I turned to CARGID, these people clearly know their job. They selected the angles, adjusted the wheel alignment in an hour. They charged 9,000 tenge, the results are excellent — the car no longer pulls to the side. Thanks for the promptness!
My husband gave us an old Volkswagen Passat, the steering wheel was heavy, and the tires were worn unevenly. At CARGID they looked and said that camber adjustment was needed. They did it, steering became easier, tire wear stopped. The price is 11,000 tenge — acceptable. Thanks, now we'll go on vacation with peace of mind.
I stopped by to check the geometry after winter tires, it was pulling a bit. At CARGID they checked everything, it turned out one angle was slightly off. They adjusted it, set it perfectly. The service cost 7,500 tenge, took half an hour. The quality of service is excellent, the staff is polite. I recommend it.
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.