

Fender repair
- Cause
- The client hit a pole in a parking lot and dented the front left fender.
- Found
- Dent without paint damage, but with a crease in the metal.
- Done
- Pulled out the metal, straightened the geometry, painted the fender.

We will restore your Land Rover's body to factory geometry and flawless appearance. We work with all models: Range Rover, Discovery, Defender — from local polishing to full restoration after an accident. We use only quality materials and provide a warranty of 24 months.
Eight types of Land Rover bodywork: from rocker panel and side member to painting and polishing

We remove the trim, cut out the rust and weld in new metal. The rocker panel once again maintains geometry and does not let moisture through.

We check the geometry, cut out the damaged section and weld in a repair insert. The side member restores the body's rigidity.

We pull and straighten the fender, apply body filler and paint it to match the body color. The part is level again and shows no signs of repair.

We remove dents up to 5 cm using levers from the back side of the panel. The factory paint coating remains intact.

We sand and polish the clouded plastic of the headlights. The light shines brightly again, and the headlight itself looks clear.

We match the color and paint only the damaged area, without repainting the whole part: we blend the edge. Minimal intervention in the factory paint.

We prepare the plastic, apply primer and paint the bumper to match the body color. The surface is uniform again and free of chips.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
We show real cases of Land Rover body restoration at our service center.
We'll give you the exact cost after a technician inspects the car. Prices are for labor; parts and materials are calculated based on brand and availability.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Paintless dent removal (up to 5 cm) | 1–2 hours | 24 mo | from 19,500 ₸ |
| Headlight polishing | 1 hour | 24 mo | from 8,000 ₸ |
| Local panel painting | 3–4 hours | 24 mo | from 12,000 ₸ |
| Bumper painting | from 1 day | 24 mo | from 25,000 ₸ |
| Fender painting | from 1 day | 24 mo | from 35,000 ₸ |
| Door painting | from 1 day | 24 mo | from 40,000 ₸ |
| Hood painting | from 1 day | 24 mo | from 50,000 ₸ |
| Roof painting | from 2 days | 24 mo | from 60,000 ₸ |
| Full car painting | from 5 days | 24 mo | from 400,000 ₸ |
| Rocker panel repair | 2–3 days | 24 mo | from 25,000 ₸ |
| Side member repair | from 2 days | 24 mo | from 40,000 ₸ |
| Fender repair (with painting) | from 2 days | 24 mo | from 30,000 ₸ |
| Anti-corrosion treatment (2 layers) | 1 day | 24 mo | from 45,000 ₸ |
| Body polishing (restorative) | 4–6 hours | 24 mo | from 25,000 ₸ |
| Raptor coating (partial) | from 2 days | 24 mo | from 70,000 ₸ |
For repairs after an accident, an additional charge is possible for geometry correction and reinforced work. The exact price depends on the vehicle's condition. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
We do rocker panels and side members with a structural seam and anti-corrosion treatment inside. At least two days — because first comes metal, then protection, not the other way around.
We straighten with hooks through the gaps, without drilling or applying body filler. The factory paint coating remains intact, and the dent is removed without repainting.
We perform local painting with blending onto adjacent parts. The blend boundary is not visible in the sun, and the bumper and fender do not differ in tone.
We cover the seam, painting and anti-corrosion treatment. If the side member or rocker panel fails, we will redo it at our own expense within the term.
We explain how body restoration proceeds — from request to vehicle pickup.

You submit a request on the website or by phone, and we select a convenient time for inspection. The technician assesses the damage, prepares a preliminary estimate and agrees on the timeframe.
request and inspection by a technician
We record the exact list of work and the cost of parts and materials in the work order.
list of work and priceWe remove the bolt-on elements, check for hidden damage, and clarify the scope of work.
finding hidden damage
We straighten the geometry, remove dents, and replace damaged parts.
geometry, dents, replacementWe apply body filler, primer, prepare the surface and match the color using the catalog.
primer and color matching
We apply paint in the booth, dry it, and polish to a factory shine. We install the parts, perform quality control, and hand over the vehicle.
camera, polishing, inspectionWalk-ins welcome. By appointment — no queue.

Send a photo of the damage, the car make and year to WhatsApp. We will give you a price range, the timeframe and help you pick a booking time.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

Land Rover body repair in Almaty starts with the question of what the damaged part is made of: Range Rover, Discovery, and Defender of different generations come with both steel and aluminum bodies. Then come disassembly and the search for hidden damage, a written estimate, metalwork, anti-corrosion treatment, and painting in the booth. The warranty on body work, painting, and anti-corrosion treatment is 24 months.
Cars of the brand from different generations are built from different materials: some have a steel body, others are almost entirely aluminum. This determines what can be straightened and what is better replaced.
| Model | Body material | What matters during repair |
|---|---|---|
| Range Rover and Range Rover Sport of the latest generations | Aluminum unibody | Aluminum requires its own technology for straightening and joining parts |
| Range Rover of previous generations | Steel body, doors, hood, and front fenders made of aluminum | Bolt-on panels and the structural part are assessed separately |
| Discovery 3 and 4 | Steel body with integrated frame | Frame, sills, and door openings after impacts and winters |
| Discovery 5 and the new Defender | Aluminum unibody | Deep dents with a crease more often end up as panel replacement |
| Classic Defender | Aluminum panels on a steel frame | Corrosion of the frame and body mounts, dents on soft panels |
| Freelander 2 and Evoque | Steel unibody, some bolt-on parts on the Evoque are aluminum | Sills, arches, and bumpers, classic steel straightening |
We start Land Rover body repair in Almaty by finding out what metal the damaged part is made of: steel and aluminum panels often sit side by side on the same car. Steel handles pulling and straightening well, then the part is leveled with a thin layer of filler and painted. Aluminum is softer, stretches more on impact, and does not tolerate overheating well, so we straighten aluminum panels where the metal allows and replace them when there is a crease or tear. There is also chemistry involved: if aluminum touches steel without insulation, corrosion starts at the joint, and fasteners and sealants for such spots are selected separately. Before body work we remove the bolt-on elements, look for hidden damage, and only then agree on the estimate. Tip: if the car has already been repaired, ask the previous owner where panels were replaced — this will save time during the inspection.
An SUV goes where a sedan won't: rocks hit the sills and underbody, and winter road chemicals settle in the arches. That's why the lower part of the body on these cars wears out faster than the top.
We repair the rockers on Range Rover and other models of the brand using the same procedure: remove the trim, cut out the rust or dented area down to healthy metal, and weld in new metal or a repair insert. We make the seam structural, not with sparse tack welds, because the rocker acts as part of the frame and maintains the geometry of the door openings. Then we apply anti-corrosion treatment inside the cavity and outside: metal first, then protection, never the other way around. On aluminum bodies of newer generations, the rocker is designed differently: we decide whether to straighten or replace it after opening it up. We put the car on a lift—we have six—so the underbody and both sides of the rockers are fully visible, without a flashlight from under the bumper. Tip: if the rocker trim is loose or sand crunches underneath, ask to have it removed during inspection, because that's exactly where rust begins.
A repaired rocker lasts a long time if you don't let dirt and salt sit on it for months. In winter, the underside of the car should be washed more often than usual: the reagent that dries in the arches and behind the rocker trims keeps working even in a warm garage. In spring, it's useful to remove the liners or at least wash the arches with a pressure washer to flush out the sand that holds moisture against the metal. Clean the drain holes in the doors and rockers with a thin wire: if water doesn't drain, the edge starts rusting from the inside. Chips on the rockers from stones should be covered immediately, before orange spots appear, because touch-up painting costs far less than welding in new metal. After serious off-roading, inspect the underbody: a dent in the floor or a bent frame bracket won't straighten itself out. Tip: photograph the rockers and arches once a season—it makes it easier to notice when a rust spot starts growing.
A bumper hit on a heavy SUV rarely ends with just a dent: the energy travels into the reinforcement, headlight mounts, and front part of the body. That's why damage assessment starts with disassembly.
Body repair of a Range Rover with accident damage almost always turns out to be bigger than it looks from the outside. Behind the bumper are the reinforcement, brackets, parking sensors, and radars for driver assistance systems; behind the fender are the liner, mudguard, and side member. That's why we remove the bolt-on parts before preparing the estimate and look for cracks in brackets, bent mounts, and shifted body points. If the side member is damaged, we cut out the damaged section and weld in a repair insert, and restore the body geometry on a frame machine. The owner often notices signs of misalignment themselves: doors close with effort, hood gaps are uneven, the car pulls to one side. We include everything found in the estimate and show it in photos, and start work only after the owner agrees. Tip: keep the broken clips and brackets from the impact—they make it easier to understand where the hit landed.
| What we check | How | Why |
|---|---|---|
| Panel gaps | Around the perimeter of doors, hood, and trunk | Even gaps confirm the geometry is restored |
| Doors and locks | Close without effort, check latching | A tight door indicates residual misalignment |
| Color and texture | Daylight, different viewing angles | A new part should not differ in shade and gloss |
| Welds and anti-corrosion | Inspection from below on a lift | The seam is covered with protection, no bare metal |
| Road behavior | Test drive | The car doesn't pull, no knocks or body squeaks |
The large smooth panels of these vehicles are clearly visible in the sun: both a small dent and a slightly different shade are noticeable. So it's important not to repaint more than necessary and not to leave a visible edge.
If a part needs painting, we match the color by catalog and paint in a spray booth where dust doesn't settle on the fresh layer. Many Land Rover colors are metallics and pearls whose shade changes with the viewing angle, so even paint exact by code may differ from the adjacent panel that has faded in the sun. To make the edge invisible, we do local painting with blending: the color is smoothly transitioned onto the neighboring area, and the clear coat is applied wider than the repair zone. We polish the dried clear coat, leveling the gloss across the entire part. As a result, the fender and bumper don't differ in tone either in the booth or outside. Tip: when picking up the car, step back a couple of steps and look at the panels in daylight at a sharp angle—that's exactly how a difference in shade is visible.
The quality of body work shows not on the day of handover but after one or two winters. So it's worth having the warranty terms and the progress of work on paper and in photos.
| Case | 24-month warranty | What we do |
|---|---|---|
| Rust along the seam of a repaired sill or side member | Yes | We redo the repair at our own expense |
| Paint defect on a repaired part | Yes | We fix the defect at our own expense |
| Anti-corrosion coating applied during repair | Yes | We restore the protection |
| New accident after repair | No | We treat it as new damage |
| Third-party intervention | No | The warranty does not cover someone else's rework |
| Part supplied by the client | No | We are responsible only for the installation work |
At key stages CARGID takes a photo report: the opened sill, the weld seam before anti-corrosion coating, the prep for paint — everything that primer and clear coat will later cover. We show the removed parts and give them back to the owner, and the choice of part stays with them: OEM, aftermarket or their own part. A service advisor handles the work order from intake to handover, and our own body master does the metal and paint work. We record the warranty term and conditions in the work order and the completion certificate, and diagnostics for a warranty case are free. Land Rover body repair in Almaty is routine work for us: over 12 years, more than 9,000 cars of various makes have come through our shop. Tip: keep the work order and the certificate until the warranty ends — with them, a disputed case is settled in one visit.
The body of this make forgives off-roading, but it doesn't forgive delayed repairs. Here's what to keep in mind before handing the car over for work.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost varies greatly depending on the damage and model. Minimal work — local painting of a scratch or chip — starts from 12,000 tenge. Fender repair with painting — from 30,000 tenge. Serious repair with body geometry and replacement of structural elements is calculated only by estimate after defect detection. We give the exact price after inspection and defect detection: they are free and take about an hour. The estimate includes work, materials, and painting.
The price depends on the complexity of the damage, the required scope of work, and the materials used. It takes into account: replacement or repair of parts (it is cheaper to straighten than to replace), body type (SUVs have thicker metal), the need for straightening, welding, painting, as well as the price of spare parts — original parts are more expensive than aftermarket. The cost is also influenced by the premium nature of the brand: high-precision equipment is required for calibrating assistants and quality materials. The final amount is stated in the estimate.
The timeframes depend on the scope of work and availability of spare parts. For complex repair: replacement of parts, painting, calibration of systems — the car is in work for 7-10 days. If rare OEM parts need to be ordered, the timeframe may increase to 14-20 days. Polishing or light local repair — from a few hours to one day. Repair of a fender or door without replacement — from 2 days. We state the exact timeframe after defect detection and clarify it when agreeing on the estimate.
For performed Land Rover body work, a warranty of 24 months is provided. It covers the quality of welding, body geometry, painting, and anti-corrosion treatment. The warranty does not cover damage resulting from new accidents or third-party intervention in body components.
Usually booking is required so that we can plan the workload of the bays and the time for your car. You can call us or leave a request on the website — we will agree on a convenient time for inspection. If you need urgent repair, call us — we may find a window in the coming days. Before starting work, we agree on all details, so a visit by appointment saves your time and guarantees that the master will be ready to accept the car.
Yes, you can bring your own spare parts, paint, or consumables. In that case, we check them for compatibility with your car and warn about possible risks: if the part is used or non-original, it may not fit perfectly, and unsuitable paint may produce an unstable shade. When installing your own spare parts, we are responsible only for the work, not for the quality of the part. We can also offer our proven materials — with them, a full warranty applies to the work.
Situations vary. If after repair you find defects (poor fit, chips, streaks on the paintwork, incorrect gaps), you come to us. We perform an inspection, and if a manufacturing defect is identified, we eliminate it free of charge under warranty. If the problem arose as a result of use (for example, due to an impact) — this is not a warranty case, but we will offer a solution for a reasonable fee. Important: act immediately, do not try to fix it yourself.
Local repair is the restoration of a small area of the body (scratches, chips, small dents) while preserving the factory coating on the rest. It is faster (from 3–4 hours) and cheaper. Full painting of a car or a separate element involves painting the entire part (for example, a fender or door) in the factory color. It is necessary for significant damage or aging of the paintwork. We use color matching with computer analysis to ensure an exact shade match.
For the first 2–3 weeks after painting a Land Rover, it is not recommended to wash under high pressure or apply wax or polish to the repaired areas. During this period, the paint coating gains its final hardness, so careful hand washing without abrasives is sufficient. After a month, you can carry out polishing and protective treatment of the body, as well as check the condition of the anti-corrosion layer on seams and hidden cavities.
Payment is accepted in cash, by bank card, and bank transfer is also possible for legal entities. No prepayment is required; the full cost is paid after the work is completed and the acceptance certificate is signed. When agreeing on the estimate, you fix the price, and it does not change during the process. If hidden damage is discovered during work (for example, corrosion), we supplement the estimate and notify you of additional expenses before starting that work.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
Got into an accident in a Discovery 4, the fender and bumper were damaged. The guys worked quickly, finished in 3 days, painted to match the color, you can't even tell. Price 250,000 tenge, adequate for such work. I recommend the service.
Brought in a Range Rover Sport after hitting a pole. The rear door was smashed, I was afraid it would take long. But after only 4 days the car was ready, new door, perfect paint, no seams visible. Thanks to master Ildar for explaining all the stages. Repaired for 350,000, as agreed.
Bought a used Discovery 3, the sills had rot. They did anti-corrosion treatment and painted for 220,000, now everything is clean. They approached it very carefully, cleaned the weld seams, painted so well you can't tell from factory. Done in 3 days, though they promised 4. Pleasantly surprised.
I had an accident in a Range Rover Vogue, the front part messed up the geometry. In CARGID they put it on the straightening bench and pulled everything out properly. It took 5 days, cost 180,000, but now it fits perfectly. Now the doors close easily, and the car doesn't pull to the side. Thanks!
Scratched the bumper in a parking lot, thought I'd have to replace it. But they offered local repair for 65,000. Done quickly, in 2 days, and the paint matched the body color perfectly. The car is like new. Very satisfied.
Recently I scratched the bumper of my car (Range Rover Evoque). They fixed it quickly at the service, painted within 2 days, the color matched exactly. I am satisfied with the service, the price was 65,000 tenge. Thank you!
I went in with the problem that the headlights had faded and were shining worse. At the service they polished them, coated with a protective compound, they became like new. For 25,000 and 1 day — excellent result. The light is now bright, the road is clearly visible.
Had a damaged side door on a Land Rover Freelander. In CARGID they replaced the door with a used one and matched the paint perfectly. The work cost 340,000, took 4 days. Everything is neat, no complaints. 24 months later they adjusted it under warranty — no problems, no issues.
In winter it iced up so much that I opened the door unsuccessfully and hit a pole. The dent on the front fender was decent. The guys pulled it out without painting — they have a technology, didn't damage the factory coating. Paid 25,000, the car was ready the same day. Fast and quality.
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.