Proper wheel alignment is the key to stability and safety of your commercial vehicle. Our technicians will perform precise adjustment of wheel alignment angles for Gazelle, UAZ and other trucks. Modern 3D equipment and experience allow us to achieve ideal parameters, reducing tire wear and fuel consumption.
Mobile wheel alignment (with mobile team visit, within Almaty)
from 2 hours
6 mo
from 35,000 ₸
Wheel alignment with additional suspension inspection (play, hub bearings)
2–3 hours
6 mo
from 24,000 ₸
Wheel alignment after replacement of springs/leaf springs
2–3 hours
6 mo
from 25,000 ₸
Wheel alignment with angle adjustment on a loaded vehicle (if cargo present)
2–3 hours
6 mo
from 29,500 ₸
Prices include labor and computerized diagnostics. Final cost may vary depending on the technical condition of the suspension and the need for adjustment work. Warranty periods — see the page «Warranty»
06
Why choose wheel alignment for Gazelle and UAZ at CARGID
Warranty.
Every promise — backed by a number or a document: work order, photos, removed parts.
6MO
warranty on labor — the term is stated in the work order.
3D alignment
Warranty
Gazelle
01
3D stand, not a ruler
We read angles with optical targets on alloy wheels: we catch both camber and caster. A ruler only gives toe and lies after suspension repair.
02
Pressure before measurement
First, we inflate the tyres to the factory norm for Gazelle or UAZ. Different pressure throws off toe by 5–7 minutes, and the measurement lies.
03
Warranty 30 days
If after adjustment it pulls to the side or the steering wheel is crooked — we will return and re-adjust for free. We cover the adjustment itself, not the wear of tie rods.
04
Master with 12 years on Gazelle
I know where to use shims, where a tie rod, and where a wedge under the spring is needed. On UAZ with a flatbed, we adjust toe under load.
07
Stages of wheel alignment for Gazelle and UAZ
Steps.
We explain how the procedure goes in our service — from booking to vehicle handover.
01
Vehicle reception
You leave a request on the website or by phone, we select a convenient time and book you for diagnostics. The technician inspects the vehicle, records the current condition of the suspension and tyres, clarifies complaints and wishes.
request on WhatsApp
02
Tyre pressure check
We bring the pressure in all tyres to the manufacturer's norm — this is a mandatory condition for precise adjustment.
inspection and diagnostics
03
Diagnostics on the stand
We install the vehicle on a 3D stand and take the current wheel alignment angles: toe, camber, caster.
estimate before work starts
04
Analysis and adjustment
We compare the readings with the norm for Gazelle and UAZ, and if necessary, adjust the angles within tolerance.
work to factory procedure
05
Control measurement
After adjustment, we take a control measurement to ensure all parameters are within norm and symmetrical.
result check
06
Test drive
We go for a short check to evaluate the vehicle's behaviour and ensure there is no pulling. We hand over the vehicle with a report of the work performed and a warranty on the result 6 months.
At CARGID, we do wheel alignment for Gazelle and UAZ in Almaty on a 3D stand with optical targets: we measure both camber and caster, not just toe. Before measuring, we inflate the tires to the factory spec and adjust the onboard platform under load. The work is covered by a 6-month warranty, recorded in the work order.
How Gazelle and UAZ Wheel Alignment Differ
The Gazelle and UAZ are built differently, which means a different set of adjustable angles. Let's break down which parameters can actually be adjusted on each model and which are set at the factory.
What's Adjustable on a Gazelle and What's Factory-Set
On the Gazelle Business, the front wheel camber is not adjustable from the factory—mainly toe is adjusted, and we tell you this upfront before starting work. The Gazelle Next follows the same layout: toe is set with tie rods and ends, and there are no separate camber adjustment elements in the design. We measure angles on a 3D stand with optical targets and compare them to the factory tolerance for each axle. If camber is out of spec due to wear or suspension repairs, turning it is pointless—we first replace the worn component, otherwise the adjustment won't hold. In practice, a Gazelle most often needs this kind of correction for exactly this reason: sagging springs or worn bushings change the geometry, and no amount of tie rod tweaking will bring it back. Before adjusting, we check the suspension and show you which part will need to be replaced.
Why UAZ Angles Drift Differently
The UAZ Patriot, Hunter, and "loaf" have leaf-spring suspension and a solid axle, so the adjustment ranges are different, and caster is not adjustable on all versions. The solid axle keeps camber virtually unchanged, but the leaf springs sag over time and alter the axle's longitudinal inclination. On the Patriot, caster is set with adjustment shims; on the Hunter and "loaf," that may not be possible at all—the angle is set by design. Pulling to the right on a straight road is more often caused by caster or play in the steering than by toe, so replacing tie rods at random without measuring all angles is pointless. A 3D stand measures both camber and caster, not just toe—so the cause of the pull is visible immediately, before disassembly. If there is play in the steering, it is fixed before adjustment; otherwise, the set angles will drift after the first few kilometers.
How Angle Adjustment Works on a 3D Stand
The sequence of steps is the same for both a Gazelle flatbed and a UAZ, but there are nuances for commercial vehicles and SUVs—pressure, load, and a control measurement. Here's how it works at our facility.
Why a 3D Stand, Not a Tape Measure
We read angles with optical targets on alloy wheels on a 3D stand—we measure both camber and caster, whereas a tape measure only gives toe and lies after suspension repairs. We attach targets to the wheels, the equipment calculates axle position across three planes, and the technician sees each wheel individually, not an average across the axle. On a UAZ with a solid axle, this is crucial: a tape measure won't show axle misalignment at all. Wheel alignment for Gazelle and UAZ in Almaty on such a stand gives precise angles for both commercial vehicles and SUVs. Six lifts in the shop allow us to keep the vehicle on the stand while suspension work is being approved—we don't move it back and forth. When springs, leaf springs, or tie rods are replaced, a tape measure will show "within spec" on a bent suspension—so we do the control check on the same stand as the initial measurement.
Pressure and Load Before Measurement
First, we inflate the tires to the factory spec for the Gazelle or UAZ, and adjust the onboard platform under load—otherwise the numbers lie. Uneven pressure throws off toe by 5–7 minutes, and "topping it up later" won't help: the readings will already be off. We place a Gazelle flatbed with a load corresponding to its working mode—an empty bed gives different values than a loaded one. We check a UAZ Patriot with the driver in place and standard ballast so the suspension settles as it would in real driving. Before adjusting, we check for play in ball joints and bushings: if a component is loose, the work is pointless. Only then do we set the pressure and start reading angles. The measurement itself takes little time, but it's the preparation that determines how accurate the readings on the stand will be.
How Long It Takes and Whether It's Realistic in One Visit
Measurement and diagnostics: we check angles and suspension play, and show the wear to the client.
Approval: a written estimate before work; we start repairs only after the owner agrees.
Replacement if needed: bushings, ball joints, tie rods—in the same visit, no second appointment.
Adjustment and control check: we set the parameters and re-check on the stand.
Test drive: before handover, we check how the vehicle behaves on the road, not just on the lift.
Documentation: the service advisor manages the work order from intake to handover, and we record the warranty there as well.
When It's Time for Wheel Alignment and What to Do After Suspension Repair
Angles don't only drift from an impact: replacing tie rods, leaf springs, and suspension lifts change the geometry. Here's when to come in for a measurement and what to do after suspension work.
Signs That Your Angles Are Off
Pulling on a straight road: the vehicle pulls to one side with the steering wheel straight, and you have to correct on every straight stretch.
Crooked steering wheel: the rim isn't centered even though the wheels are going straight—the first sign of misaligned toe.
Uneven wear: the tread wears on the inner or outer edge while the center remains almost intact.
Suspension impact: hitting a curb or pothole bends tie rods and changes wheel geometry.
Suspension work: replacing tie rods, leaf springs, or coil springs requires re-measuring the angles.
Play in the steering linkage: knocking and free play in the steering prevent precise toe adjustment.
Suspension Lift and Spring Replacement on a UAZ
After a lift kit on a UAZ Patriot, the angles go out, and we bring them back to factory tolerance on a 3D stand. A raised body changes the position of the control arms and throws off caster — the longitudinal tilt of the steering axis, which affects straight-line stability. When measuring angles on a UAZ Patriot during leaf spring and elastic element replacement, we check the running gear: we look at the bushings, ball joints, and play, because with sagging or reinforced components the old rubber parts behave differently. We do wheel alignment on a UAZ Patriot during a lift and spring replacement with a check of caster and toe. We take measurements with optical targets and set tire pressure to the factory spec in advance. The higher the body lift, the more important caster is: without checking it, the vehicle becomes unstable at speed, even if the toe is set.
Parts and related work in one visit
Angle adjustment is often combined with repair of worn suspension components. Below is the list of operations we put into a single work order, and the inspection procedure before measurement.
Replace bushings and ball joints or just adjust as is
If the bushings or ball joints are worn, we replace them first and then set the angles — otherwise the adjustment won't hold and the technician's work is wasted. On the Gazelle and UAZ, these components work under load and on dirt roads, so worn control arms and joints are a common cause of the steering pulling to one side. A worn bushing creates play that reads on the stand as floating toe: the readings drift from one pass to the next. We measure the parameters, show the owner the play in the suspension, and only proceed with parts replacement with their consent. The service advisor manages the work order through to handover, and we take photo reports at key stages — the photos show which components were replaced and how the angles were set.
What work we do in a single work order
operations in a single work order
Work
What we check
What we do
Wheel alignment with suspension check
play, worn components
measurement and adjustment
With bushing replacement
condition of control arms
replacement and re-measurement
With ball joint replacement
play in the ball joint
replacement and setting
After spring replacement
body geometry
angles to tolerance
For flatbed models
toe under load
adjustment under load
Warranty and what to do if the vehicle pulls after adjustment
We record the warranty on the adjustment in the documents, and if the vehicle pulls after the visit, we handle it as a warranty case. We explain the terms and the procedure.
What warranty covers wheel alignment and where it's recorded
We give a 6-month warranty on wheel alignment; the term and conditions are recorded in the work order and the completion certificate when the vehicle is handed over. The warranty covers the work performed and the parts we installed. The service advisor handles the paperwork: he manages the work order from intake to handover, so the warranty terms don't get lost between stages. The certificate shows exactly which operations were performed and which parts were installed. We show the old parts and give them to the client — that way it's clear what was replaced. For a warranty case, diagnostics are free. The warranty does not cover an accident after repair, third-party interference, natural wear of consumables, or a part brought by the client. That's why we inspect the client's part before installation and warn about the risks: the warranty does not apply to parts brought in by the client.
If the vehicle pulls to one side after adjustment
If the vehicle pulls after adjustment, come in — we do warranty diagnostics free of charge and find the cause. The pull isn't always in the angles: the cause can be a sticking caliper or uneven tire pressure, so we start with a check, not with re-adjustment. First we inflate the tires to the factory spec for the Gazelle or UAZ and check how the vehicle behaves on a test drive. Uneven pressure throws off toe by 5–7 minutes and the measurement is wrong — that's the first thing we rule out. Then we check the suspension and brakes: a seized caliper pulls to one side just like a misaligned camber. The 3D stand reads angles with optical targets on alloy wheels and captures both camber and caster, so a re-measurement shows the real picture. If the cause is our work, we fix it at no charge.
Gazelle and UAZ Alignment: Key Differences
We've gathered what most often determines the result of wheel alignment on commercial Gazelles and UAZ SUVs — briefly, without repeating what's already covered, and based on practice.
Different design: on the Gazelle, mainly toe is adjusted; on the UAZ, caster matters too.
Measurement on the stand: a 3D stand captures camber and caster; a ruler only captures toe.
Pressure and load: tires are inflated to spec, and flatbed models are adjusted under load.
After suspension repair: a lift, spring and tie rod replacement require re-measuring the angles.
Warranty in the documents: the term and conditions are recorded in the work order and certificate at handover.
10
Frequently asked questions about wheel alignment for Gazelle and UAZ in Almaty
Questions.
Price, timeframes, warranty, payment — 10 questions asked most often.
10
Didn't find an answer?
Message us on WhatsApp — a service advisor will reply within 5 minutes.
The cost of wheel alignment for a Gazelle and UAZ at CARGID is from 17,000 tenge. This price includes adjusting wheel alignment angles on a modern 3D stand and checking all suspension parameters. If additional work is required, for example, replacing tie rod ends or adjustment due to severe wear of parts, the cost may be higher, but we always agree on the final amount before starting work. Discounts are also possible for comprehensive servicing.
Usually the procedure takes about 40-60 minutes. This time includes installing the car on the stand, checking current angles, adjustment, and control measurement. If the suspension is heavily worn or there are deformations, more time may be needed — up to 1.5 hours. We try to do the work quickly, but without compromising quality, so the exact time depends on the condition of your car.
Yes, we provide a warranty on wheel alignment for 30 days or 3,000 km of mileage (whichever comes first). The warranty is valid provided that during this period you have not been in an accident, have not changed suspension parts, and have not performed independent adjustment. If the angles go off due to our fault, we will perform a repeat adjustment free of charge. The warranty is confirmed by a receipt and a note in the work order.
An appointment is not required, but desirable. On weekdays there are usually free slots, you can come without an appointment — the waiting time will be no more than 15-20 minutes. On weekends and in the evening there is a load, so we recommend calling and making an appointment in advance. Making an appointment takes a couple of minutes, and you will be sure that you will be accepted on time. Just call us, tell us the car make and a convenient time.
For wheel alignment specifically, you don't need to bring anything — we use our own fasteners and components for adjustment if necessary. However, if during diagnostics it turns out that spare parts are required (for example, tie rods, ends), you can bring your own. But note: we do not guarantee the quality of parts installed by us if they are not ours. If in doubt, it is better to consult with us in advance.
If you notice that after the procedure the car pulls to the side, the steering wheel is not straight, or there are other deviations, return to us within the warranty period. We will check the wheel alignment angles free of charge and fix the problem. Most often the cause is worn suspension parts that were not detected during the initial diagnostics, or incorrect tire pressure. We will perform a repeat diagnostics and eliminate the cause.
The differences are due to the suspension design: Gazelles (especially Business and Next) have a more modern front suspension on transverse arms, while UAZs (Hunter, Patriot) have a dependent leaf-spring or coil-spring suspension with a solid axle. Because of this, the adjustment ranges are different. On a Gazelle, camber and toe angles are more often adjusted, on a UAZ — mainly toe, camber may be non-adjustable. Our master takes these features into account to achieve optimal parameters for a specific model.
Immediately after the procedure, try not to hit potholes and not to drive over curbs at high speed — this can knock off the settings. It is recommended to check tire pressure and inflate if necessary. During the first week, avoid sharp maneuvers and transporting heavy loads if this could change the ground clearance. It is also worth periodically checking the condition of tie rods and ends, as their wear leads to misalignment.
Main signs: uneven tire wear (the inner or outer edge wears out), the car pulls to the side when driving straight, the steering wheel is not centered, steering wheel vibration at speed. It is also recommended to do wheel alignment after suspension repair (replacing arms, ball joints, tie rods), tire replacement, after strong impacts (potholes, accidents). In general, experts advise checking wheel alignment every 10,000–15,000 km of mileage.
Payment is accepted in cash, by card, and by bank transfer. The service is performed on the day of request if there is no queue and takes from 40 to 90 minutes depending on the model and condition of the adjustment units. The cost depends on the number of adjustable axles and the need for preliminary suspension preparation.
11
What drivers say about our Gazelle and UAZ alignment
Reviews.
We collect ratings on the website and on maps — we hide nothing.
4.8
872 reviews on the website 1 900+ ratings in total
Aslan
Came in a Gazelle Next after replacing tie rod ends. They did the wheel alignment quickly, turned it around in an hour. The car stopped pulling to the right, the steering wheel became just right. Price 15,000, not expensive. I liked the service, polite guys.
Dmitry
UAZ Patriot, after a suspension lift it started eating tires. The guys adjusted camber, toe, caster. Now the tires wear evenly, the car holds the road better. It cost 25,000, I paid without questions because they did everything in front of me, showed me on the stand.
Yerzhan
Gazelle Business, the steering wheel was crooked after suspension repair. I made an appointment, arrived, they did it in 40 minutes along with checking tire pressure. The steering wheel was set straight, the car goes straight. The price is reasonable — 18,000 tenge. Thanks!
Sergey
UAZ Hunter, they did wheel alignment after replacing the leaf springs. They accepted me without an appointment, quickly, but the master explained everything in detail: what was wrong, what they did. The result is excellent, the car became more obedient. I paid 20,000 tenge — fine.
Aigul
They did wheel alignment on a UAZ Profi. There was a problem with the rear wheels — they were standing like a house due to overload. The guys adjusted it, said to watch the weights. Price 20,000, they did it neatly, gave a guarantee. Thanks!
Ivan
Gazelle 3302, I suspected wheel bearings, but it turned out the camber was wrong. The master showed on the stand how the wheels were crooked. They adjusted it, the hum disappeared, the tires now wear evenly. I paid 15,000 tenge, was satisfied.
Timur
UAZ Bukhanka, I did wheel alignment, but we have leaf springs! I thought it wouldn't work. But they did it, though they had to install adjustment plates. But now the car goes straight, the steering wheel doesn't shake. Price 22,000 — ok.
Olga
Gazelle Next, after replacing suspension arms the camber went off. We came to CARGID, they did everything quickly, in 50 minutes. They adjusted the toe, and the camber too. The car became more manageable, smoother. Thanks to the master, he explained everything, gave recommendations.
Vladimir
UAZ Patriot, at speeds above 80 it started to wander. It turned out the toe was off. They made adjustments, and also checked tire pressure. Now it goes like on rails. I paid 18,000, I consider this a fair price for such work.