

Peugeot 408: oil darkened
- Cause
- Scheduled oil change, mileage 60,000 km.
- Found
- The oil is dark, with a burnt smell, but no shavings.
- Done
- Drained the old oil, filled with fresh oil (75W-80), replaced the plug.

Peugeot 307, 308, 408 and other models with manual transmission require transmission oil changes every 60–90 thousand km. We use original oils and equivalent oils, strictly following the regulations. We work with warranty of 6 months for the service, and provide on-site service across Almaty.
Oil and seal replacement works in Peugeot transmission

We drain the old oil from the gearbox, flush it, and fill with new oil according to the norm. The gearbox runs smoother, and wear on parts is reduced.

We remove the transmission pan, clean the surfaces, and install a new gasket. We stop oil leaks and protect the gearbox from dirt.

We replace the rear crankshaft seal to stop oil leakage between the engine and the gearbox. At the same time, we check the condition of the flywheel.

We replace the input shaft seal of the gearbox. We eliminate oil leakage into the clutch and extend the service life of the unit.

We replace the half-shaft seal at the output of the gearbox or differential. We stop oil leakage and protect the CV joint from dirt ingress.

We drain the old oil from the differential, flush it, and fill with new oil. We reduce noise and wear on the final drive gears.

We drain the old oil, replace the oil filter, and fill with new oil. The engine receives clean lubrication and protection from wear.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
Below are examples of completed Peugeot manual transmission oil change jobs: reasons for contact, what we found, and the result.
The exact cost depends on the model, volume, and condition of the transmission. Below are basic services.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Manual Transmission Oil Change (without material) | 1–2 hours | 6 mo | from 12 000 ₸ |
| Manual Transmission Oil Change (with oil) | 1–2 hours | 6 mo | from 15 000 ₸ |
| Manual Transmission Pan Flushing | 30–60 min | 6 mo | from 5 000 ₸ |
| Pan Gasket Replacement | 1–2 hours | 6 mo | from 4 000 ₸ |
| Crankshaft Seal Replacement | 2–3 hours | 6 mo | from 9 000 ₸ |
| Input Shaft Seal Replacement | 1–2 hours | 6 mo | from 7 000 ₸ |
| Half-Shaft Seal Replacement | 1–2 hours | 6 mo | from 6 000 ₸ |
| Differential Oil Change | 30 min | 6 mo | from 10 000 ₸ |
| Manual Transmission Diagnostics | 30–60 min | 6 mo | from 3 000 ₸ |
| Shift Linkage Adjustment | 30–60 min | 6 mo | from 3 500 ₸ |
| Engine Oil Change (with oil and filter) | 1 hour | 6 mo | from 18 000 ₸ |
| Power Steering Fluid Change | 30 min | 6 mo | from 8 000 ₸ |
| Transfer Case Oil Change | 1–2 hours | 6 mo | from 14 000 ₸ |
| Automatic Transmission Oil Change | 2–3 hours | 6 mo | from 15 000 ₸ |
Prices are indicated without the cost of oil, unless otherwise specified. For exact cost and timing, please inquire by phone or WhatsApp. On-site service is free when ordering a service. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
We replace the pan gasket and the plug sealing ring. The old ones get crumpled during removal — we do not reinstall them, otherwise it will leak.
We replace the input shaft seal and half-shaft seal on site, without removing the transmission. The client saves on removal and installation and does not risk the fastening.
We set the volume according to the control hole or dipstick, not «by eye». Underfilling kills the bearings, overfilling squeezes out the seals.
If a leak appears after replacing the seal or gasket — we fix it again at our expense. We cover specifically the tightness of the joints.
We explain how the manual transmission oil change for Peugeot is performed at our service — from request to vehicle handover.

You submit a request on the website or by phone, and we select a convenient time for your visit. The technician receives the vehicle, clarifies the mileage and service history, and records the condition of the manual transmission.
request on WhatsApp
We check the oil level and condition, and inspect the gearbox for leaks and damage.
inspection and diagnosticsThe vehicle is lifted on a hoist, the drain plug is unscrewed, and the used fluid is drained into a container.
estimate before work starts
If necessary, we remove the pan, clean it from deposits, and replace the gasket.
work to factory procedureWe fill the manufacturer-recommended oil of the required volume through the filler hole.
result check
We warm up the gearbox and check the oil level, topping up to the norm if necessary. We conduct a test drive, ensure proper operation, and hand over the vehicle to the client with a warranty.
warranty in the work orderWalk-ins welcome. By appointment — no queue.
CARGID car repair team. 8–17 years of experience.
Author
Mobile auto electrician

Car alarm and car stereo installer

Auto electrician

Roadside assistance technician

Diagnostic technician

Engine mechanic (cylinder head repair)

Auto electrician and diagnostician

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

At CARGID, we change the oil in a Peugeot manual transmission and set the volume by the check hole or dipstick, not by eye. We install a new pan gasket and drain plug ring, and replace seals without removing the gearbox. The warranty on the work is 6 months, and the terms are fixed in the work order.
Oil in a manual transmission ages unnoticed, but the gearbox gives its first signals tens of thousands of kilometers before a breakdown. Let's break down what's normal and what's a reason to come to the lift.
According to the schedule, oil in a Peugeot manual transmission lasts 60–90 thousand km, but in city driving, Almaty traffic jams, short trips, and heat dictate their own terms — we recommend changing at 45–60 thousand km. Short trips don't let the gearbox warm up, condensation accumulates inside and accelerates lubricant aging, and summer heat adds thermal load on the bearings. Over 12 years of repair, we've seen many gearboxes where the change was done strictly by mileage, but a dense sediment remained at the bottom — that's why during service we offer to flush the manual transmission sump. If the car is driven mainly in the center and sits in traffic jams, focus on the lower limit of the interval: a mileage-based calculation without adjusting for driving conditions is misleading, and second-gear crunching appears before the scheduled interval. Changing the oil in a Peugeot 307 manual transmission follows the same principle — tied to driving conditions, not just the number on the odometer.
Specification and volume are the two things most often skimped on during a change. We show how we select oil for a specific gearbox and why we set the level by the check hole or dipstick.
In Peugeot 307, 308, 408, and Partner manual transmissions, we pour transmission oil according to the manufacturer's specification — 75W-80 or 75W-90 depending on the gearbox, and we accept your own oil if it meets the specification. We select by VIN and unit marking: a 307 with a 1.6 engine and a 308 may have different housings, and there's no "universal" fluid here. At our shop, the client chooses what we pour — OEM, aftermarket, or oil brought from home; if there's doubt about the specification, we first check the canister against the spec, then pour. We do the work in two options: with material, when we select the oil ourselves, and without material, if you brought your own. Mixing different transmission oils when topping up is not allowed — additives conflict, and the gearbox starts working harsher; if you don't know what's filled, it's better to do the full procedure.
We set the fill volume in a Peugeot manual transmission by the check hole or dipstick, not by eye — on a specific gearbox it might be 2.1 L, and deviation in either direction is critical. On some units, the level is checked by overflow from the fill plug: we don't stop filling until oil flows back. On other models, we rely on the dipstick, and here a level lift is important — on a slanted car, the mark is off by a few millimeters. We inspect the input shaft seal and axle shaft seal before filling: if there's already seepage, the new level will only make it worse. Underfilling kills gearbox bearings, overfilling pushes out seals — both scenarios cost more than an accurate fill by the mark.
An oil change isn't just drain and fill. We break down what's included by default, what related operations we do, and why some consumables are replaced every time.
We replace the manual transmission pan gasket and the plug O-ring every time we remove them — the old ones get crushed, and we don't put them back, otherwise it will leak. Rubber loses elasticity over years in the gearbox and holds its shape only when pressed: remove the pan, and a groove mark remains that won't seal the fit anymore. Same with the drain plug ring — copper or rubber, it's crushed once. Both parts are consumables, and we include them in the estimate right away so we don't come back to leaks a month later. The client sees the old parts when picking up the car: the question "why pay for consumables that seem intact" is settled on the spot — based on actual wear, not words.
We replace the input shaft seal and axle shaft seal on a Peugeot on-site, without hanging the gearbox — the client saves on removing and installing the transmission and doesn't risk the mounts. Access to the input shaft opens after removing the gearbox only on some models; on most Peugeot units, the seal comes out from the clutch side with the housing separated, and the axle shaft is removed from the hub without dismantling the transmission. At the same time, we check the crankshaft seal replacement — if there's already seepage from the engine side, it's wiser to close both units in one go. If the axle shaft seal is only seeping, it's not yet a reason to pull it — the leak progresses with heat, and oil leaves faster than it seems from drops on the parking lot.
| Work | When Needed | What We Check |
|---|---|---|
| Manual transmission oil change | By interval or signs | Level by check hole or dipstick |
| Manual transmission sump flush | Oil change, high mileage without service | Presence of shavings and sediment |
| Pan gasket replacement | Every time the pan is removed | Sealing after tightening |
| Input shaft seal replacement | Leak at the gearbox-engine joint | Oil traces on the transmission housing |
| Axle shaft seal replacement | Seepage or leak at the drive | Play and boot condition |
| Shift linkage adjustment | Hard gear engagement | Shifter and rod travel |
Gearboxes on Peugeot of different years differ, and there's no single volume and specification for all. We break down how servicing a Peugeot 307 manual transmission differs from a 308 and what we check on commercial versions.
The 307 and 308 use different gearboxes, so the oil spec and the way you check the level are different too — one has a dipstick, the other uses a check hole. The 307 more often has a unit with a dipstick you can use to see the fluid condition; on the 308 the level is set at the check hole in the case until oil starts running back out. We pick the spec by the gearbox, not by the model in the listing: both cars come with different engine–transmission pairings. We fill by the dipstick or check hole, not by a reference figure. If the owner doesn't know which gearbox is in their car, the volume and spec are matched by VIN, not by the model in the listing — that rules out a filling error. A Peugeot manual transmission oil change in Almaty on the 307 and 308 follows these same principles of matching the spec and checking the level.
On the 408, Partner and Boxer the approach is the same — spec and volume by the specific gearbox — but the commercial versions more often have seal leaks because of the loads. The Partner and Boxer carry cargo and work on the road, so the half-shaft and input shaft seals go earlier than on the passenger 307 and 308. We replace the half-shaft seal on the spot without removing the gearbox — the client saves on removal and installation. On the 408 the gearbox is closer to the passenger versions, and complaints are more often about bearing noise from underfilling than about leaks. On the Boxer and Partner with high mileage, when servicing the oil it's worth inspecting the half-shaft seals right away — in commercial use they go earlier than on the passenger 307 and 308.
Warranty and turnaround are what an owner wants to know before booking. We explain exactly what the warranty on gearbox work covers, how long the procedure takes and how to get into the shop without a wait.
We give a 6-month warranty on Peugeot manual transmission work; the term and conditions are written into the work order and the handover report when the car is released. The warranty covers the work performed and the parts installed, and we do the diagnosis on a warranty case free of charge. It does not cover an accident after the repair, third-party interference, normal wear of consumables, or a part the client brought in. These boundaries are written in the documents, not just "word of mouth" — at handover the staff member goes over every point. In my view, an honest report listing the conditions matters more than verbal promises: in a dispute you open the paper and see what was included in the work. Before signing, check the type of work and the term in the work order — that's how you lock in the shop's responsibility for the whole warranty period. A Peugeot manual transmission oil change also falls under this warranty, so we record its conditions in the same documents.
The Peugeot manual transmission procedure itself takes about an hour, and longer with diagnosis and seal work; we're open daily from 09:00 to 20:00, by appointment — no wait. The car is received by the service advisor, who handles the work order through to handover, and we do a test drive before release. If you plan to bring your own oil, say so when booking — the specialist will check the spec in advance and tell you whether it fits your gearbox, so the work doesn't have to be redone. Reception address: 129 Mukagali Makataev Street. In our experience, a morning appointment frees up the day: by 11:00 the car is already on the lift, and you pick it up before evening. Come with some buffer for diagnosis — that way the staff member has time to assess the seals and pan gasket before disassembly.
To sum up: we've gathered the main things to keep in mind before a Peugeot manual transmission oil change — in a short list, without extra detail or repetition.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost of a manual transmission oil change for Peugeot at our car service ranges from 8,000 to 15,000 tenge. The final price depends on the car model, the type and volume of oil, and the condition of the gearbox. It includes draining the old oil, replacing the pan gasket (if needed), filling new oil, and checking the level. The exact cost can be quoted after diagnostics.
Usually the procedure takes from 1 to 1.5 hours. This time includes removing the engine guard, draining the used oil, replacing the gasket (if necessary), filling fresh oil, and checking the level. If additional cleaning of the pan or replacement of seals is required, the time may increase to 2 hours.
For a manual transmission oil change for Peugeot, a warranty on the work is provided — 6 months or 10,000 km of mileage, whichever comes first. The warranty covers the correct selection of oil according to Peugeot specifications and the absence of leaks through the drain and fill plugs. If after the change noise or difficulty shifting gears related to our work appears, we fix it under warranty.
Yes, for a manual transmission oil change for Peugeot we schedule in advance — usually 1 day ahead, to prepare the oil of the required specification and sealing rings for the plugs for your model. The procedure itself takes from 40 minutes to 1.5 hours depending on the gearbox model and the replacement method — partial or with full drain. When booking, specify the model, year, and engine volume of the Peugeot.
Yes, you can use your own oil, filters, and gaskets. We do not charge extra for using your materials. However, if you have doubts about the quality or compatibility of the oil with your manual transmission, our technicians can advise and recommend the optimal option.
If after a replacement done elsewhere you have problems (noises, difficulty shifting gears, leaks), come to us. We will perform diagnostics, assess the condition of the oil and gearbox, and if necessary replace the oil again while eliminating the cause, for example, by replacing the gasket or seal. The work is paid separately, but you will be confident in the result.
We do a standard replacement (draining the old oil and filling new oil through the fill hole) and a full replacement with system flushing (removing the pan, cleaning deposits, replacing the gasket). We can also change the oil with filters if the design provides for it. The choice of method depends on the condition of the oil and the manufacturer's recommendations.
After an oil change, it is important not to overload the gearbox for the first 200-300 km: avoid hard starts and towing. Check the oil level after 2-3 weeks (according to the instructions). Watch for any leaks under the car. Usually manual transmission oil is designed for 60-80 thousand km of mileage, but under intensive use it is worth changing more often.
You can pay for a manual transmission oil change for Peugeot in cash, by card, or by transfer. The cost consists of the price of oil according to Peugeot specifications, the fill volume for your gearbox, and the work; for a change with flushing or pan removal, the price is higher. We quote the final amount before starting work after inspection.
We use oils recommended by the manufacturer Peugeot: usually Total BV 75W-80 or equivalents (e.g., Motul, Mobil). The specification and volume depend on the gearbox model (usually from 1.8 to 2.5 liters). When ordering, you can specify, but if you haven't brought your own, we will select the optimal option.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
Finally found a service that truly understands Peugeot. I changed the gearbox oil on a 308. The guys did everything quickly, advised on the oil, showed me the old one — it was almost black. After the change, the gears started engaging more precisely, the noise disappeared. The price of 18,000 tenge is reasonable.
Stopped by to change the manual transmission oil on a Peugeot 408. They did it according to the regulations, replaced the 75W-80 oil and the plug. Everything was neat, the technician explained that the oil had already served its time. The level was checked, no leaks. I recommend.
Changed the gearbox oil on a Peugeot 3008. There was a small leak, I thought it was something serious. Turned out to be just the pan gasket. They replaced it, filled new oil, the leak is fixed. Thanks for the honesty and reasonable prices.
Peugeot 207, bought it second-hand, the gearbox oil hadn't been changed for about five years. The service suggested flushing the system and replacing the filter screen. They did it in one day. Now the gearbox works like new, the noise is gone. Excellent work.
I changed the manual transmission oil on a Peugeot 508, there were jerks when shifting. The technicians immediately determined that the oil was contaminated. They flushed the gearbox, filled fresh oil. The jerks disappeared, the car drives smoothly. Thanks for the professionalism.
I came in about vibration on a Peugeot Partner. Turned out to be a low oil level and worn bearings. They replaced the oil and bearings. The vibration is gone. The price is 35,000 tenge, but it was worth it. I'm satisfied with the work.
Car is a Peugeot 308, manual transmission oil change. Done quickly, with quality, original oil was filled. The old oil had metal shavings, good thing it was noticed in time. Now the gearbox works quietly. I recommend
Oil change on a Peugeot 408. Everything was honest, they showed how much was drained, told about the condition of the gearbox. The price is like in the city, maybe even a bit lower. Thanks for the service!
Peugeot 3008 cars, manual transmission oil replacement. The work was done well, quickly. They showed the old oil, poured in the new one. No problems at all. Thank you!
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.