Authorexperience

Oil change in the engine, automatic transmission, transfer case, and differentials of Jeep Grand Cherokee WK2. We use MANN, Castrol, RAVENOL oils. We work with gasoline and diesel engines 3.6, 5.7, 3.0 CRD. 6-month warranty on all work. Book today — we'll do it the same day!
Oil change work in the engine, transmission, transfer case, and differentials of Jeep

We drain the old oil, replace the oil filter, and fill with new oil. We check the level and make sure there are no leaks.

We drain the old fluid, replace the filter if necessary, and fill with new fluid. We check the level and the operation of the transmission.

We drain the used oil from the manual transmission and fill with new oil. We monitor the level and the condition of the drain plug.

We change the oil in the transfer case: drain, fill with new oil, check the level. It ensures the operation of the all-wheel drive.

We drain and fill the oil in the front differential, check the level. It protects the gears and bearings from wear.

We change the oil in the rear differential: drain, fill, check the level. It extends the service life of the final drive gears.

We flush the engine with a special fluid, then fill with new oil and replace the filter. It removes sludge and contaminants.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
We will calculate the exact cost after inspection. Minimum prices are shown.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Engine oil change (petrol) | 40 minutes | 6 mo | from 9 500 ₸ |
| Engine oil change (diesel) | 1 hour | 6 mo | from 11 000 ₸ |
| Automatic transmission oil change (partial) | 1 hour | 6 mo | from 15 000 ₸ |
| Automatic transmission oil change (machine) | 2 hours | 6 mo | from 25 000 ₸ |
| Manual transmission oil change | 1 hour | 6 mo | from 8 000 ₸ |
| Transfer case oil change | 1 hour | 6 mo | from 8 000 ₸ |
| Front differential oil change | 1 hour | 6 mo | from 7 000 ₸ |
| Rear differential oil change | 1 hour | 6 mo | from 7 500 ₸ |
| Power steering fluid change | 1 hour | 6 mo | from 6 000 ₸ |
| Oil change with engine flush | 1.5 hours | 6 mo | from 12 000 ₸ |
| Oil and filter change (package) | 2 hours | 6 mo | from 17 000 ₸ |
| Engine oil change with coolant | 2 hours | 6 mo | from 10 000 ₸ |
| Engine oil change with brake fluid | 1.5 hours | 6 mo | from 9 000 ₸ |
| Engine oil change with filters (oil, air) | 1.5 hours | 6 mo | from 11 000 ₸ |
| Engine oil change with suspension diagnostics | 1.5 hours | 6 mo | from 12 000 ₸ |
| Engine oil change with gasket replacement | 2 hours | 6 mo | from 14 000 ₸ |
| Engine oil change with decarbonization | 3 hours | 6 mo | from 20 000 ₸ |
The cost of oil and filters is calculated separately. Please check availability and price when booking. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
We replace the plug ring and the filter gasket. The old ones harden and leak — with new ones it stays dry until the next change.
On the 3.6 and 5.7 we remove the pan and install a new filter with a gasket. Without disassembly, the filter cannot be replaced.
Before filling with fresh oil, we run a flush until the drain is clean — old dirt does not consume the new oil.
We cover leaks at the plug and pan. If it leaks after the change, we will redo it for free.
We explain how an oil change at CARGID works: from booking to the final check.

You submit a request on the website or call. The manager clarifies the model, year, and current mileage. We choose a convenient time and agree on the cost of the work, oil, and filter in tenge.
request on WhatsApp
The technician receives the car and records the initial condition and your requests in the work order.
inspection and diagnosticsWe check the engine for leaks and select oil according to the specifications specifically for your Jeep.
estimate before work starts
We unscrew the drain plug, let the oil drain completely, and replace the sealing ring if necessary.
work to factory procedureWe remove the old filter, clean the mounting surface, and install a new oil filter.
result check
We fill the exact amount of oil according to the manufacturer's regulations, check the level with the dipstick, and start the engine. We check for leaks, reset the service interval, and hand over the car along with the documents.
warranty in the work orderWalk-ins welcome. By appointment — no queue.
CARGID car repair team. 8–17 years of experience.
Author
Mobile auto electrician

Car alarm and car stereo installer

Auto electrician

Roadside assistance technician

Diagnostic technician

Engine mechanic (cylinder head repair)

Auto electrician and diagnostician

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

CARGID performs Jeep oil changes in Almaty for all units — engine, automatic transmission, manual transmission, transfer case, differentials, and power steering. We start with diagnostics and a written estimate, and work begins only after your approval. The oil change warranty is 6 months, and the timeframe and terms are recorded in the work order. We're open daily 09:00–20:00 by appointment.
On a Jeep, lubrication isn't just in the engine: the transmission, transfer case, axles, and power steering have their own circuits. Here's what units we service and how the service formats differ.
We service all lubrication circuits on a Jeep — engine, automatic transmission, manual transmission, transfer case, front and rear differentials, and power steering, not just the engine. Our Jeep oil change in Almaty starts with the service advisor recording each unit separately in the work order: the engine has one interval and one filter, the transmission has a different volume and procedure, and the transfer case and axles have their own plugs and seals. The schedule differs for gasoline and diesel versions, and for automatic transmissions we offer a partial or machine-assisted option. The transfer case and differentials on a Jeep operate under constant load, so their lubricant ages faster than the mileage suggests, and it's worth checking at every scheduled service.
| Option | What happens | When it's appropriate |
|---|---|---|
| Partial | We drain and refill part of the volume | Scheduled maintenance, low mileage |
| Machine-assisted | We displace the old fluid completely | Regular care, known history |
| With engine flush | We run flush until the drain is clean | Dirty drain, long overdue |
The Grand Cherokee WK2, Wrangler, and different engines have their own nuances — from removing the oil pan to the electronic dipstick. Here's how the procedure differs on the gasoline 3.6 and 5.7 and the 3.0 CRD diesel.
On the 3.6 Pentastar and 5.7 HEMI engines, we remove the oil pan and install a new element with a gasket — the part can't be changed without disassembly. On the Pentastar, the consumable is inside the crankcase, not outside like on many inline fours, so access opens only after the pan is removed. The 5.7 HEMI is similar: the old gasket hardens from heat, and during reassembly it's replaced along with the drain plug O-rings. We also inspect the pan for dents and traces of sealant from previous visits. A Jeep Grand Cherokee oil change with this disassembly takes longer, but the new filter actually works instead of clogging immediately. If you don't replace the consumable, fresh oil quickly gets contaminated through the clogged element, so saving on disassembly leads to a repeat procedure sooner than scheduled.
We select the lubricant based on the specifications for the specific engine — gasoline and the 3.0 CRD diesel have different ones, and we fill the volume according to the schedule. For the 3.6 Pentastar and 5.7 HEMI, it's the MS-11106 specification with the viscosity the manufacturer prescribes for the climate and mileage; for the 3.0 CRD diesel, it's the MB 229.51 approval and a low-ash requirement because of the particulate filter. For gasoline engines, API SN compliance is also important — it covers protection against piston deposits. We calculate the volume from the engine's data sheet, not by eye: overfilling on the HEMI is just as harmful as underfilling — it pushes out the seals. A product without the required approval eventually causes carbon buildup and wear, and on the diesel it also clogs the particulate filter — so the approval matters more than the brand on the can.
Some Jeeps don't have a physical dipstick — we check the level with an electronic sensor via a dealer scanner and confirm it after filling. The electronics on the WK2 and Wrangler show not only the level but also the lubricant condition by mileage, and on the 3.0 CRD diesel they add particulate filter data. We fill the exact volume per the schedule, then warm up the engine and read the values again — this shows whether the fluid has settled unevenly in the pan. The sensor is sensitive to measurement conditions, so it's best to check the level on a level surface and after the lubricant has drained, otherwise the readings are off. Measuring on a slope or with a cold engine gives an error of several millimeters on the dipstick — with an overfill, that's already critical for the seals.
We show the car's journey through the shop — from check-in by the advisor to the test drive before pickup. At every stage, the owner understands what's being done to the car and why.
The car is received by the service advisor, who also manages the work order through to pickup, and we start the Jeep oil work only after a written estimate and the client's approval. A Jeep oil change follows one procedure: first diagnostics, then a written estimate, and only after approval — the work. First diagnostics: we inspect the pan, plug, condition of gaskets and seals, and determine whether only the consumable is needed or also a filter with O-rings. The estimate lists the items and scope of operations, and the advisor explains each line. We start after the client approves the list — no surprises during the process. If something else is found along the way, such as a weeping crankshaft seal, it's approved separately. A written estimate before starting protects against unexpected charges: any additional item is discussed with the owner, not added silently. In our practice, this procedure saves time for both sides — disputed invoices don't arise.
An engine oil change takes less time than a transmission service, and before handover we do a test drive and check for leaks. Engine oil on the lift is the quickest: drain, new filter, fill and level check. The transmission takes longer — especially with a machine flush, where the fluid has to be run through the circuit. We take photos at the key stages and show you the old parts and hand them over. After the work the car goes on a test drive: the technician checks that the pressure light isn't on and there are no seeps under the pan or at the joints. Most often the leak comes not from the gasket itself but from the old drain plug washer — so we replace it right away, otherwise in a couple of days the car comes back with a spot under the pan. We install a new washer and filter gasket on every work order.
We break down the consumables that get changed along with the oil, and why small things like a washer decide whether it stays dry under the car until your next visit.
We run the flush until it drains clean, which takes about 30 minutes, when the old oil is dark or the car has gone a long time without service. The order is: drain the old oil, pour in the flush fluid, start the engine and wait until a clear stream comes out of the plug instead of dark sludge. On the Pentastar 3.6 and HEMI 5.7, after 10–15 minutes of running the fluid usually comes out cloudy — that's normal, the sludge is being washed off the internal surfaces. On the 3.0 CRD diesel the procedure takes longer: there's more soot, and the stream doesn't clear on the first pass. A flush isn't always justified — on a clean engine with regular service it's a waste of time, but old dirt without it eats fresh oil faster and the next service comes sooner than scheduled.
We break down exactly what our warranty covers after an oil change, which cases it doesn't include, and how responsibility is handled if you bring your own consumables.
We give a 6-month warranty on an oil change and record the term and conditions in the work order and the completion certificate at handover. Coverage applies to the work performed and the parts installed: seal washers, the filter gasket, and the filter itself if we supplied it. Diagnostics for a warranty case are free — the service advisor takes in the car and manages the work order through to handover, so the service history for a specific vehicle is never lost. Coverage does not include accidents, third-party interference or natural wear of consumables — worth knowing in advance. In my view, what matters more is this: the term and conditions are on paper, not just words, so in a disputed situation you don't have to prove what was done and when in our shop.
You can bring your own oil and filter — the choice of OEM, aftermarket or customer parts is yours, and the warranty on the work still applies. We note in the work order that the consumable is the customer's, and from there we're responsible for the quality of the procedure itself: plug torque, installing the washer, the filter gasket, and no leaks after assembly. The warranty does not cover a part brought by the customer — if the oil or filter turns out to be wrong, there's no one to make a claim against. In our experience, it's better to take a questionable consumable from us: then responsibility for the result rests entirely with the service, including redoing the work. And this isn't a formality — if a filter looks doubtful, the technician will say so before work starts, not afterward.
Summing up on Jeep oil changes: what really affects the life of the units and what to look at when choosing a service and consumables for your car.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost of a Jeep oil change at CARGID depends on the model and engine type. Base price for labor starts at 9,500 tenge (for Jeep Grand Cherokee with a 3.6 petrol engine). For diesel and V8 engines, the labor cost is higher - from 7,000 tenge. We will provide an exact price after clarifying the model and year of manufacture. It includes draining the old oil, replacing the oil filter (if required), and checking the level. The cost of oil and filter is calculated separately.
A standard Jeep oil change takes 30-40 minutes. If additional diagnostics are needed or there are difficulties accessing the filter (for example, on some diesel models), the time may increase to 1 hour. In any case, we try to finish within minimal time so you don't waste time.
The warranty covers the work itself: correct selection of oil and filter for the specific Jeep model, proper installation of the filter, and absence of leaks after the change. If within the warranty period a leak appears at the drain plug or filter, we will fix the issue again free of charge. The warranty does not cover consumables and does not apply to engine malfunctions not related to the oil change.
We recommend booking in advance, especially on weekends and evenings. This allows us to prepare the necessary oil and filters, and you to avoid waiting. You can book by phone or via WhatsApp. If you come without an appointment, we will try to accept you on a first-come, first-served basis if there are free lifts.
Yes, you can bring your own oil and filter. We will accept them and perform the change. However, in this case, we are not responsible for the quality of materials, and the warranty on the work will only apply to the tightness of the system. Please note: for Jeep it is important to use oil with API SN approval or higher, and we can check if your oil is suitable – if not, we will warn you.
If after the oil change you find a leak or other malfunctions caused by our work, contact us immediately. We have a 6-month warranty: we will fix any defects related to the change free of charge. We also check the quality of work before handing over the car to minimize risks.
We offer two main options: express change (without removing the skid plate, if present) - faster and cheaper, but access to the drain plug and filter may be limited. Full change includes removing the skid plate if it gets in the way, which provides better access to components and a more thorough change. For Jeep with high clearance (e.g., Wrangler), the skid plate is rarely removed, while for Grand Cherokee it is often. Exact prices are in the price list on this page.
After an oil change, we recommend avoiding high RPMs and sharp accelerations for the first 300–500 km so the new oil distributes evenly. Check the oil level a couple of days after the change (cold engine). Follow the change interval recommended by the manufacturer (usually 10,000–15,000 km for petrol and 7,500–10,000 km for diesel). Use quality fuel and oil with appropriate approvals.
Payment is accepted in cash, by bank card, and by transfer; after the work we issue a receipt or closing documents. The cost depends on the Jeep model and engine, oil volume, filter type (original or aftermarket), and chosen oil. We provide the exact amount after selecting the oil by VIN or engine brand, before starting work.
We use motor oils from well-known brands (e.g., Mobil, Castrol, Shell) with approvals recommended for Jeep. For 3.6 and 3.0 petrol engines, 5W-30 or 0W-20 is usually required; for 2.0 CRD diesel - 5W-30. The oil volume depends on the model: Grand Cherokee 3.6 - about 5.6 liters, Wrangler 3.6 - 5.7 liters, Cherokee 2.4 - 4.7 liters. We will clarify the exact volume by VIN code.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
Had the oil changed in a Jeep Grand Cherokee, 5.7 engine. Drove into the garage as I arrived - thought it would take about 40 minutes, but they finished in an hour. Castrol 5W-30 oil, Mann filter, everything done neatly. Cost came to 40,000 tenge, fine. Thanks to the mechanic, he also checked the level and antifreeze. The car runs noticeably better.
Had an oil change on a Jeep Renegade. Brought my own oil, filter from the service. Price for the work - 5,000 tenge, fast and precise. Liked that they drain the old oil completely, unlike some. They took it in the same day, even though there was no appointment. Recommend.
Had the oil changed in a Jeep Compass, first time at this service. Called, they scheduled for the next day. Accepted normally, explained which oil is better for city driving. An hour later I picked up the car. Receipt for 29,000 tenge, Mobile 1 oil. I don't understand much, but the mechanic showed everything on the dipstick. All honest.
Jeep Wrangler, 3.6 petrol. There was no complaint, just the time came according to the service book. Changed the oil to 0W-20, filter and plug. All in 45 minutes. It came to 32,000 tenge, I confirm the price and timing. I recommend.
Spent a long time choosing where to go for an oil change in a Jeep Patriot. A friend recommended CARGID. No regrets: booked in advance, everything done without waiting. Castrol oil filled, original filter. Receipt for 33,000 tenge, timeframe - 1 day. The manager even called afterwards, asked if everything was ok. Nice.
Oil change on a Jeep Grand Cherokee diesel. The mechanics said the wrong oil had been filled, so the engine was noisy. Changed to the correct 5W-30, filter. It became quieter. Price - 45,000 tenge for oil and labor, took half a day because they waited for the engine to cool down. Satisfied.
Changed the oil on a Jeep Cherokee, the car is already older, 2008 year. Replaced the oil, filter, and also cleaned the throttle body - this is a separate job. The amount is 50,000 tg, but this includes oil change and cleaning. Everything is ok, but it took 3 hours. In principle, normal.
Stopped by for an oil change in a Jeep Wrangler before a trip to the mountains. Done quickly, took 5W-40 oil - they said it's the one for our hot summers and mountains. They gave me the old filter to show. Everything under control. Paid 36,000 tenge. Driven already 3000 km, all good.
First time changing oil in a Jeep, had no idea what and how. At the service everything was explained in detail: what oil, how many liters, what filter. Changed in 40 minutes, receipt for 30,000 tenge, Mobil oil. The car runs smoother. Excellent service, will come again.
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.