

Kia Sportage
- Cause
- Small animals settled in the engine compartment
- Found
- A nest, fur and droppings found on the engine guard
- Done
- Steam cleaning of the entire engine compartment, odor elimination, drying

Steam cleaning effectively removes oil stains, dirt and dust without damaging the electronics or wiring. Safe for the engine and the engine bay. We carry out the procedure in 1-2 hours with a quality guarantee.
List of engine steam cleaning services: from standard to complex cleaning.

We clean the engine with hot steam under pressure. The steam dissolves dirt and oil without flooding the electrical system.

We apply a degreaser to the engine compartment, then rinse with steam. We remove oil film and stubborn dirt.

We partially remove the skid plate to reach the lower part of the engine. We wash hidden cavities.

We insulate connectors, ECU, and alternator before washing. We protect electronics from moisture, then clean with steam.

We clean the belt, pulleys, and water pump with steam. We remove dirt and oil from attachments without disassembly.

After washing, we dry and blow the compartment with compressed air. We remove remaining moisture from connectors and hard-to-reach areas.

We remove oil leaks and dirt on the transmission. We use steam and degreaser for tough areas.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
Real examples of our work with explanations.
Safe steam cleaning of the engine bay from oil, dust and dirt with electrical protection.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Diagnostics of the engine and engine bay condition before washing | 20 minutes | 30 days | from 2 000 ₸ |
| Steam generator engine washing (V-shaped engines) | 1–2 hours | 30 days | from 12 000 ₸ |
| Steam generator engine washing (inline engines) | 1–2 hours | 30 days | from 10 000 ₸ |
| Steam generator engine washing (boxer engines) | 2–3 hours | 30 days | from 15 000 ₸ |
| Steam generator engine washing (diesel engines) | 2–3 hours | 30 days | from 14 000 ₸ |
| Local steam washing of the injector and fuel rail area | 30–40 minutes | 30 days | from 5 000 ₸ |
| Steam generator cleaning of the engine oil pan and oil filter area | 30–50 minutes | 30 days | from 4 500 ₸ |
| Engine bay washing with pre-degreasing | 1.5–2.5 hours | 30 days | from 13 000 ₸ |
| Engine washing with the crankcase protection removed (with partial dismantling) | 2–3 hours | 30 days | from 16 000 ₸ |
| Engine washing with full electrical insulation (connectors, ECU, alternator) | 2–3 hours | 30 days | from 18 000 ₸ |
| Steam cleaning of the auxiliary components (belt, pulleys, water pump) | 30–45 minutes | 30 days | from 5 500 ₸ |
| Removal of oil stains and old deposits from the engine block | 1–1.5 hours | 30 days | from 8 000 ₸ |
| Urgent engine washing (same-day appointment) | 1.5–2 hours | 30 days | from 15 000 ₸ |
| Mobile steam generator engine washing (within Almaty) | 2–3 hours | 30 days | from 20 000 ₸ |
| Engine washing with subsequent drying and compressed air blow-off | 2–3 hours | 30 days | from 17 000 ₸ |
| Repeat engine washing (within 30 days after the first one) | 1–2 hours | 30 days | from 8 000 ₸ |
| Engine washing with heavy contamination (oil drips, dirt on the transmission) | 2–3 hours | 30 days | from 19 000 ₸ |
| Engine washing for a truck (up to 10 t) | 2–3 hours | 30 days | from 25 000 ₸ |
| Engine washing for an SUV with underbody protection | 2–3 hours | 30 days | from 16 000 ₸ |
| Comprehensive engine bay washing with cleaning of all plastic elements | 2–4 hours | 30 days | from 22 000 ₸ |
Prices are indicated in tenge and depend on the degree of contamination and the type of engine. The cost includes materials for electrical protection. The exact price will be quoted by the technician after inspection. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
We cover the alternator, fuse box, and connectors with waterproofing. Water does not get into the wiring, you start without errors.
After washing, we blow all connectors with compressed air and dry for 40 minutes. Moisture does not remain in spark plug wells.
We wash with the skid plate removed: we reach the oil pan and attachments. We put back all clips and bolts.
We use a steam generator at 150–170 °C: dirt comes off without aggressive agents. Plastic and hoses are not corroded.
From request to clean engine: 6 clear steps.

You submit a request on the website or by phone, we find a convenient time for your visit. A mechanic inspects the engine compartment, determines the degree of contamination, and covers sensitive components.
inspection and insulation of components
We remove major dirt and dust so that steam can penetrate deeper into hard-to-reach areas.
removal of heavy dirtThe equipment reaches operating temperature, providing sterile dry high-pressure steam.
steam generator warm-up
We treat the engine with steam, evaporating oil leaks and dirt from surfaces.
steam treatmentUsing brushes and microfiber, we remove softened dirt from hoses, valve cover, and other elements.
brushes and microfiber
We dry the engine compartment with compressed air, especially connectors and wiring. We check engine start, ensure there are no errors, and hand over the car to you.
drying and start-up checkWalk-ins welcome. By appointment — no queue.
Car wash team. 5–16 years of experience.
Author
Senior interior deep cleaning specialist

Body polishing specialist

Car wash administrator

Car wash and drying specialist

Pre-sale car preparation specialist

Body polishing technician

Headlight polishing specialist

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

Our steam engine cleaning in Almaty starts with an inspection and isolating the electrical components: the alternator, fuse box, ECU, and connectors are covered with waterproof protection. Then we clean the engine with 150–170 °C steam, blow out the connectors with compressed air, dry for about 40 minutes, and check that the engine starts. We provide a 30-day warranty on the work.
The engine doesn't have to shine, but dirt and oil under the hood interfere with cooling, hide leaks, and attract rodents that like a warm engine bay.
Our steam engine cleaning in Almaty starts with an inspection of the engine bay. The technician checks how dirty the engine is, whether there are fresh oil leaks, where the control units, connectors, and alternator are located, and whether there are any exposed or damaged wires. This determines the preparation and the time needed: fresh dust comes off with one steam treatment, while years of oil buildup require a degreaser and more time. If the car has non-standard equipment, such as an additional alarm or a gas system, we take that into account as well. The engine type matters: an inline engine is cleaned faster, while on a V-twin or boxer some components are hidden deeper. Before starting, the technician gives the final price and time, and only after the owner agrees does the car go to the bay.
A regular pressure wash is faster and cheaper, but it's after that kind of cleaning that people most often come in with misfires, dashboard errors, and corroded connectors.
Pressure washing the engine bay forces moisture into places it shouldn't go: sensor connectors, spark plug wells, ignition coils, and the fuse box. Water lingers in tight spots and takes days to dry, and during that time the contacts corrode. The result is familiar to many: the engine starts to misfire, the RPMs fluctuate, errors light up on the dashboard, and sometimes the car simply won't start. The aggressive chemicals often used for engine washing at regular car washes dry out plastic and rubber hoses, making them stiff and cracked prematurely. A strong jet can tear off hood insulation and labels. So even on an engine that's clean on the outside, what matters is not so much washing off the dirt as not leaving moisture inside the electrical system.
| Parameter | Steam | Pressure water |
|---|---|---|
| Moisture after washing | Evaporates quickly | Remains in connectors |
| Oil buildup | Dissolves with heat | Requires strong chemicals |
| Plastic and hoses | Don't dry out or stiffen | Suffer from chemicals |
| Risk to electrical system | Minimal with insulation | High |
| Water consumption | Low | High |
Steam handles most dirt, but it has its limits. If the engine has been covered in oil for years due to a leak, the buildup turns into a hard crust, and steam alone isn't enough: first you need a degreaser to soften the deposits, and then the hot treatment. Steam doesn't eliminate the cause of the dirt. If a seal or gasket keeps leaking, in a few weeks oil will cover the block again, so it's better to show the clean engine to a technician right away and find the source. Don't expect a cosmetic miracle on old plastic either: faded covers will become clean but not new. However, steam does a good job removing organic matter, dust, traces of rodents, and odors that regular water handles worse.
The safety of the wash is decided before the steam generator is turned on, not during the work itself, so preparation takes a noticeable part of the time in the bay.
Before washing, we cover the alternator, fuse box, electronic control unit, and exposed connectors with waterproof protection. We use moisture-resistant film and tape that fit tightly around the component and don't come off from hot steam. We pay special attention to places where connectors face upward or sit in recesses where condensation can accumulate: that's where water collects the most. If the technician notices a cracked connector or a wire with damaged insulation, he first shows it to the owner, because such a component is vulnerable during any wash. The materials for protecting the electrical system are already included in the price. We also separately cover the air intake to keep moisture out of the intake. After insulation, the technician checks once more that all sensitive components are reliably covered.
We remove the skid plate when we need to reach the oil pan, the lower part of the engine, and the accessories. Over time, dirt, sand, and oily grime accumulate under the skid plate, and washing the engine from above without touching the bottom is pointless: the leak you're after may be right underneath. We lift the car on the hoist, remove the skid plate carefully, keeping all clips and bolts, and after washing we put it back with the full set. At the same time, we can see the condition of the oil pan and the oil filter area, and the technician immediately informs the owner of any leaks found. If the skid plate is badly rusted and the bolts won't come loose, we discuss this before starting work so as not to damage the fasteners. This kind of wash takes longer but gives a complete picture of the engine's condition.
The steam treatment itself takes less time than preparation and drying, and it's not worth skimping on the latter if the car is to start without errors.
We steam clean engines at 150–170 °C. First we remove the heavy dirt and dust, then the steam generator comes up to working temperature and the technician treats the engine in sections, top to bottom. The hot steam softens the oil film and deposits, and they come off without harsh chemicals, so plastic and hoses don't get eaten away. Heavy oil spots and years of buildup we pre-treat with a degreaser and then rinse off with steam. The loosened dirt on the valve cover, hoses and air filter housing we take off with brushes and microfiber. We can also clean the injector area, the oil pan and the accessories separately: the belt, pulleys and water pump. The steam is applied point by point instead of flooding the whole bay, so not much moisture is left after the treatment.
When the wash is done, we blow out the connectors with compressed air and dry the engine for about 40 minutes. The blow-out pushes the remaining moisture out of the crevices, spark plug wells and sensor connectors where steam could have gotten in despite the insulation. Then we take off the waterproofing, check that it's dry underneath and let the bay air out. Only after that does the technician start the engine and watch how it runs: the idle should be steady and no errors should show up on the dashboard. If the car has a skid plate, we put it back on with all its hardware. You can't hand the car back right after the wash: moisture left in the wells can cause a misfire on the way home. So we don't cut the drying short, even if the owner is in a hurry.
A clean engine stays that way longer if you know what to expect in the first days after the wash and when it's worth coming back to the technician.
Sometimes moisture still finds its way into a connector, especially on older cars with cracked boots. The signs are rough idling, a misfire, an error on the dashboard in the first hours. Usually it goes away on its own once the bay warms up while driving, but there's no need to wait a few days. It's better to call right away and come in: the CARGID technician will blow out the connectors, check the spark plug wells and coils, read the errors with a scanner and clear them. If the problem is related to our work, we do everything free of charge under the warranty. Don't take the connectors apart yourself or spray anything into them, that can damage the clips and contacts, and then the repair goes beyond a simple drying. The sooner you come in, the easier and faster the technician will find the cause.
Steam cleaning is a gentle way to get the engine bay in order, as long as the prep and drying are done as carefully as the treatment itself. Here's what's worth remembering.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost depends on the engine type and how dirty it is. Steam cleaning costs from 10,000 tenge for inline engines, from 12,000 for V-shaped, from 14,000 for diesel, and from 15,000 for boxer engines. If the engine is heavily oiled, pre-degreasing is required — from 13,000 tenge. The technician will give you the exact price after inspection.
On average, the procedure takes 1–1.5 hours. If the engine is heavily contaminated (especially on diesel vehicles or after oil spraying), the time may increase to 2–2.5 hours, as more thorough cleaning of hard-to-reach areas is required. We do not chase speed; the main thing is quality, because engine cooling and reliability depend on cleanliness.
Yes, the warranty is 30 days. It covers the quality of cleaning: if after the procedure you find streaks, weak spots, or we missed something, we will fix the shortcomings free of charge upon a repeat visit. We also guarantee that we will not damage the electrical system or plastic elements. To maintain the warranty, we recommend performing diagnostics after cleaning (paid separately) to ensure there are no hidden problems, but this is not mandatory.
Booking is desirable but not strictly required. We work by prior reservation to guarantee you a convenient time and no queues. If you arrive without a booking, we will try to accommodate you, but during peak hours there may be waits. You can book by phone or via WhatsApp; just provide the car model and a convenient time. On weekdays there are usually slots, but on weekends it is better to book 1–2 days in advance.
We strongly advise against using third-party products. The reason: the steam generator operates at high temperature and pressure, and not all chemicals are safe for heat treatment. The wrong composition can damage plastic parts, rubber seals, and electronics. We use professional products that are selected taking into account engine characteristics and are safe for the steam generator. If you have special requests, discuss them with the technician before the procedure.
First, don't panic. Sometimes after cleaning moisture can get into electrical connectors, causing temporary errors. Usually everything resolves itself a few hours after drying. If the problem does not disappear, return to us within 30 days — we will check and fix the consequences free of charge if they arose due to our fault. In any case, our warranty covers damage caused by the procedure, so you are protected.
The key difference is the use of dry steam under pressure and a temperature of 150–170 °C. Steam effectively removes oil deposits and dirt without leaving moisture, which is critical for electronics. Regular pressure washing can flood the electrical system and cause contact corrosion. A steam generator is also more environmentally friendly — water consumption is minimal, and there is no risk of short circuits. The result is a perfectly clean engine without moisture settling.
We recommend not driving on dusty roads for 2-3 days so that less dirt settles. Once a month, you can wipe the engine with a damp cloth without chemicals. It is also useful after cleaning to apply a protective treatment to plastic parts with a special product — this extends cleanliness and prevents fading. If you regularly steam clean the engine every 6-8 months, it will remain in ideal condition.
Payment in cash, by bank card (Visa, Mastercard), online transfer to Kaspi, and also payment by QR code is possible. An invoice can be issued both to an individual and to an individual entrepreneur/LLP (for legal entities). If you need a receipt and a certificate of completion — that is provided. For large jobs, post-payment is possible after you are satisfied with the quality.
The procedure is completely safe if the technology is followed. We protect electrical connectors and sensitive units with moisture-proof bags or tapes. Steam does not create excessive moisture — it is in the form of dry steam, which evaporates quickly without risking a short circuit. Over the years, we have cleaned hundreds of such cars — not a single breakdown due to the steam generator. The main thing is to entrust the work to experienced technicians.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
I contacted CARGID after oil leaks appeared on my Toyota Camry. They did the steam generator cleaning in an hour, price 12,000 tenge. Everything is clean, the engine is like new, the smell of oil is gone. Very satisfied!
Nissan X-Trail, there was a smell in the cabin when I turned on the heater. The guys suggested steam cleaning the heating system. They did it for 9500, the smell is gone, the air is clean. A month later everything still works great.
Mercedes C250, after a trip out of town it started to start poorly. At the service they immediately identified water in the connectors. They cleaned with a steam generator, dried it, and starting became excellent. 14800 tenge, not expensive for such a rescue.
Kia Sportage, a mouse got into the engine compartment. It's horrible how much debris they cleaned out with steam. They did everything carefully, without smell, just perfect. Thanks for your patience and professionalism, 11,200 tenge.
Hyundai Solaris, the engine was covered in black carbon deposits. Steam generator cleaning at CARGID exceeded expectations – it became clean as from the factory. 8700 tenge, took a little over an hour. I recommend.
Volkswagen Polo, after dry cleaning elsewhere there was a terrible smell of chemicals. Here they washed with steam – the smell disappeared, everything shines. Price 10,300 tenge, but now it's safe for health.
Toyota Land Cruiser, the engine got filthy after off-roading. I took it to CARGID, they did steam cleaning. Absolutely great – dry, clean, no errors. The price was 15,500 tenge, and they gave a warranty.
My BMW X3, greru k okraske, jenschili na par generator in CARGID. All clean, no water, no zapah. 13 900 tenge, works perfect. Thanks!
Renault Duster, drove in the mountains, all the dirt from under the hood. Steam wash is top at CARGID! Protected, cleaned, dry connectors. 10 800 tenge, the car is like new. Thanks.
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.