Authorexperience

A car's wiring is like the circulatory system: the slightest damage and starting issues begin, lights go out, the engine stalls. We find and fix any electrical faults: from a broken wire to harness replacement. Diagnostics — from 5,000 ₸, a detailed report before work begins, 12-month warranty. We'll restore the factory scheme or carefully modify it for your needs.
What wiring repair includes: from broken wires in doors to starter power circuits.

We restore wires torn from constant bending in the door grommet. The client gets working window regulators, locks, and speakers.

We replace oxidized pins and broken retainers in connectors. Contacts hold tightly again, and signal dropouts stop.

We test lighting circuits and clean contacts from oxidation. The light works steadily, without flickering or loss of brightness.

We repair the power circuits for starting and charging. Voltage drop disappears, the engine starts confidently, and the battery charges.

We solder twists and restore insulation in the power and signal circuits. Sound plays without crackling, interference, or cutouts.

We check circuit integrity with a meter and look for an open or short. The client gets the exact location of the fault, not guesses.

We find the broken wire inside the grommet, solder it, and insulate the joint. The circuit works reliably, without breaking again at the bend.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
Diagnostics, fixing breaks and short circuits, harness replacement — for all makes and models.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Computer diagnostics of electrical system (checking units, sensors, circuits) | 1–2 hours | 12 mo | from 5 000 ₸ |
| Visual inspection of wiring and search for obvious defects | 30 min | 12 mo | from 2 000 ₸ |
| Circuit continuity test with multimeter (integrity check) | 1 hour | 12 mo | from 3 500 ₸ |
| Repair of wire break in corrugated tube (soldering, insulation) | 1–2 hours | 12 mo | from 4 500 ₸ |
| Replacement of a single wire (power, ground, signal) | 1–2 hours | 12 mo | from 6 000 ₸ |
| Repair of harness in door transition (broken wires) | 2–3 hours | 12 mo | from 10 000 ₸ |
| Elimination of short circuit in wiring | 2–4 hours | 12 mo | from 12 000 ₸ |
| Replacement of fuses and relays (on-site) | 30 min | 12 mo | from 1 500 ₸ |
| Repair of connectors and blocks (replacement of pins, retainers) | 1–2 hours | 12 mo | from 5 500 ₸ |
| Restoration of body ground (cleaning, new bolts, wire) | 1–2 hours | 12 mo | from 8 000 ₸ |
| Replacement of engine wiring harness (removal/installation) | from 1 day | 12 mo | from 45 000 ₸ |
| Replacement of interior wiring harness (including dashboard) | from 2 days | 12 mo | from 80 000 ₸ |
| Repair of headlight and taillight wiring (continuity test, contact cleaning) | 1–2 hours | 12 mo | from 5 000 ₸ |
| Repair of starter and alternator wiring (power circuits) | 2–3 hours | 12 mo | from 9 000 ₸ |
| Repair of audio system and head unit wiring (resoldering, insulation) | 1–2 hours | 12 mo | from 4 000 ₸ |
| Installation of additional equipment with connection (alarm, camera) | 3–6 hours | 12 mo | from 15 000 ₸ |
| Emergency on-site electrical repair (citywide) | 1–3 hours | 12 mo | from 12 000 ₸ |
| Routing new wiring for auxiliary lights (winch, light bar) | 2–4 hours | 12 mo | from 8 000 ₸ |
Prices are for labor only, excluding the cost of parts and consumables. The exact cost depends on the car make and complexity of the defect — free estimate after diagnostics. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
In the door transition, we don't twist wires but solder them and put on heat shrink. A twist there breaks within a month from vibration.
First we check power and ground at the connector with a multimeter, then open the harness. That way we don't replace a good wire for nothing.
A typical break in a door or headlight is fixed within a shift. If the wiring is complex, we agree on the timeframe after testing.
We give a year on the restored section and connections. If contact is lost again, we will redo it for free.
We show every stage — from diagnostics to vehicle handover.

You call or message us, describe the symptoms, and we find a convenient time. Computer scanning and circuit testing with a multimeter to pinpoint the break.
scanner and circuit testing
We explain the fault in detail and state the cost and timeframe before starting repairs. If necessary, we order original harnesses, connectors, and wires for your vehicle.
estimate and partsWe restore circuits, replace damaged sections, solder, and insulate connections.
soldering and insulation
We test the electrics: lights, starter, sensors — making sure everything works reliably.
lights, starter, sensorsWe perform a repeat diagnostic under load to rule out hidden defects.
re-check under load
We hand over the keys, provide a warranty on the work and operating tips.
warranty in the work orderWalk-ins welcome. By appointment — no queue.
Auto electrics team. 5–19 years of experience.
Author
Car alarm installation technician

Mobile auto electrician

Car computer diagnostics technician

24/7 auto electrician

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

Car wiring repair in Almaty starts with locating the damage: a scanner shows the faulty circuit, and multimeter measurements pinpoint the exact section. We restore wires by soldering and heat shrink, replace oxidized connectors and harness sections, test circuits under load, and provide a 12-month warranty on the restored section.
Wiring doesn't wear out evenly. It fails where it's constantly exposed to vibration, moisture, heat, and other people's hands, so the failure points are surprisingly similar across different cars. Knowing them helps the technician find the damage faster.
| Cause | Where it shows up | What we do |
|---|---|---|
| Constant bending | Door corrugated tube, trunk lid | Replace the wire section, solder the joints |
| Moisture and road chemicals | Connectors under the hood and bumper | Clean contacts, replace the connector block |
| Heat | Wires near the engine | Replace the section with heat-resistant wire |
| Vibration | Harness mounts, terminals | Restore the fastening and contact |
| Aftermarket splices | Alarm, head unit, extra lights | Remove twist splices, redo the connection |
| Rust under the bolt | Ground points on the body | Clean the pad, install a new bolt |
An oxidized contact and a poor ground cause the most confusing faults. The wire seems intact, but resistance at the contact point grows, and under load the voltage drops: the headlights dim when the fan turns on, the gauges flicker, and control units log errors that at first glance aren't related. Body ground suffers from rust under the mounting bolt, especially on cars that have survived several winters with road chemicals. We find such places by voltage drop: a measurement between the engine ground and the body under load immediately shows where current is lost. Restoring the ground means cleaning the pad down to bare metal, a new bolt, and, if necessary, a new wire. After that, several "unexplainable" faults often disappear at once—faults for which the owner was already about to replace sensors. That's why checking grounds is part of the search for almost any intermittent fault.
Opening a harness is easy, but putting it back neatly is much harder. That's why the damage location is first found with instruments, and only then is the trim removed.
We start car wiring repair in Almaty with measurements, not by removing trim. First, the scanner shows which module detected the fault and in which circuit. Then the technician takes four multimeter readings right at the consumer's connector: is there power, is there ground, does the signal pass, and is current leaking where it shouldn't. The results show where to look — in the consumer itself, in the connector, or in the section of the harness between them. That way we don't replace a whole wire for nothing and don't tear apart half the interior for one corroded contact. If the circuit is long, we divide it into sections and test them one by one until we find the spot with the lost contact. We quote the price and timeline after the search, before the repair begins. This approach saves time and lets us show the owner the exact location of the fault, not just a vague diagnosis of "something with the wiring."
Finding the break is half the job. The other half is connecting the wires so the repaired section doesn't become a new weak spot a couple of months later. Whether the car comes back with the same failure depends on how the connection is made.
We solder the repaired section and cover it with adhesive-lined heat shrink that keeps moisture out of the connection. We don't use twists even as a temporary fix: in a door transition, a twist breaks from vibration, and under the hood it corrodes and starts to heat up. We replace damaged strands with wire of the same gauge and similar insulation so the section handles the same load and temperature. We stagger the joints along the length of the harness instead of bunching them in one spot, otherwise the harness becomes thick and stiff in one place. After soldering, we return the harness to its factory corrugated tube and braiding and secure it at the factory mounting points so it doesn't rub against the body. If new connectors and wires for a specific model are needed, we order OEM parts and agree on the timeline in advance. Before reassembly, we test the section under load to make sure the solder joint carries the current.
| Method | Reliability | Where it's appropriate |
|---|---|---|
| Twist with electrical tape | Low, corrodes and heats up | Nowhere, we don't use it |
| Crimp with a sleeve | Medium, depends on the tool and sleeve | Low-current circuits without vibration or moisture |
| Soldering with heat shrink | High, sealed | Most circuits, door transition |
| Replacing a harness section | High | Long insulation damage |
| New connector housing | High | Burned pins, broken retainers |
An impact and water damage wiring in different ways. What they have in common is that the consequences often don't show up right away but weeks after the incident, when the connection to the cause is no longer obvious.
After an impact, a harness can be pinched or torn where everything looks intact from the outside. The most commonly affected are the wiring for the headlights, parking sensors, and radiator fan in the front, and the taillights and camera in the rear. Body repair adds its own risks: when a fender is replaced or a frame rail is pulled, the harness is removed, and during reassembly it's easy to pinch it with a panel or leave it unsecured. We inspect the wiring in the impact area as a whole, test the circuits, and check connectors for cracks in the housing. Harness repair in these cases is usually local: we replace damaged sections, install new connector housings, and restore the fasteners. If the car is still at the body shop after an accident, it's better to check the wiring before painting — afterward it will be harder to reach the harness, and disassembling it again will cost more than the check itself.
Three wiring areas come to the technician more often than the rest. Each has its own causes of failure and its own repair method — and therefore its own signs that it's time to see a technician.
Car wiring repair in the door transition is one of the most common jobs. The wires in the boot between the pillar and the door flex every time the door opens, and after a few years the strands break inside insulation that looks intact. At first the failure is intermittent: the window regulator works on and off, the lock doesn't always engage, the speaker crackles. Then the circuit drops out completely. We pull the harness out of the boot, find the breaks by testing continuity, replace the damaged sections, and solder the joints with heat shrink. A typical door break is fixed in one day. It's important to replace the entire worn section, not just the obviously broken strand: the neighboring wires have gone through the same number of cycles and will break soon after. After reassembly, we check every door function while opening and closing, and secure the harness so it doesn't bend at a single point.
In lighting and starting circuits, it's not just intact wires that matter — it's the contact under load. A headlight can glow dimly because of a corroded connector that shows no problem at idle but loses voltage under load. Starter and alternator power circuits carry high currents, so a burnt terminal or a torn engine ground strap causes sluggish starting and an undercharged battery. We check these circuits by measuring voltage drop during cranking and with accessories switched on. Damaged power wires are replaced as a whole, and terminals are crimped and protected from moisture. After the repair we check the lights, starter and sensors, then run diagnostics again under load. We give a 12-month warranty on the restored section and connections.
Wiring fails in predictable places, and a careful repair with the right connections restores its reliability for years. Below is what an owner should know before tackling wiring themselves or going to a shop.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionComputer diagnostics of the electrical system — from 5,000 ₸, fixing a broken wire in corrugated tubing — from 4,500 ₸, repairing a harness in the door transition — from 10,000 ₸. Engine wiring harness replacement — from 45,000 ₸, cabin harness — from 80,000 ₸. We give the exact price after diagnostics and fix it in the work order before work starts.
A local issue — a broken wire or an oxidized connector — usually takes 2–3 hours to fix. Finding a hidden short circuit and replacing a section of the harness takes 1–2 days, full harness replacement — 2–3 days. We give the exact timeframe after diagnostics and record it in the work order.
Yes, wiring repair comes with a 12-month warranty. It covers soldering, connections, and the wires and connectors we install: if contact is lost again in the repaired area, we'll redo it free of charge. The warranty does not cover external damage, accidents, or third-party interference.
An appointment is recommended but not required: we'll take you without one if a technician is free. With an appointment, the bay and technician will be ready when you arrive, so you won't have to wait. We're open daily from 9:00 to 20:00.
Yes, you can bring your own wires, connectors, and materials — the technician will check whether they fit your car. If a problem comes from the customer's materials, the warranty doesn't cover them. Usually our technicians pick the right gauge wires, terminals, heat shrink, and corrugated tubing themselves.
Come in for diagnostics — it will show the problem spots and mistakes from the previous repair. Most often it's twists without soldering, poor insulation, and wrong fuses. We'll put the wiring in order and give a warranty on our work, and you shouldn't put it off: a bad contact heats up and can cause a fire.
Partial repair means replacing a connector, terminal, fuse, or fixing a break in a single wire. Local repair means replacing several wires or a section of the harness, while a full replacement requires removing the interior and dismantling the harnesses. If oxidation and damage run along the entire length, a full replacement is better, otherwise failures will keep coming back.
The main signs are fuses that keep blowing, flickering headlights and buttons, unstable operation of devices, and a battery that drains fast. Warning signs are the smell of burnt insulation, sparking, and errors on the dashboard. With symptoms like these, don't put off your visit: wiring problems can knock out safety systems.
Don't wash the engine bay with harsh chemicals or high pressure so water doesn't get into the connections. Periodically inspect the wiring in areas of friction and heat, and don't overload the electrical system with extra devices. Keep an eye on the battery terminals, and if you smell burning or notice new faults, come to the service center right away.
You can pay in cash, by bank card, via Kaspi QR or by transfer; for legal entities, by bank transfer. Payment is after the work is completed and checked; prepayment is only needed when ordering expensive components. After the work, we issue a receipt and a work order with warranty.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
Thanks to the guys from CARGID! Toyota Camry 2020, the power windows stopped working. I thought it was something serious, but they found a broken wire harness in the corrugated tube in a day and restored everything. The price was 28,000 tenge, which is cheaper than what official dealers charge for diagnostics alone. The car is like new now. Special thanks for showing photos of the old wiring before and after.
I came with a problem: my Audi A6 started stalling while driving. Very scary, especially during rush hour. The technicians ran diagnostics, found oxidized contacts on the crankshaft sensor. They cleaned everything, soldered, replaced the connector. I've been driving for a month now — not a single error. Thanks for your patience and explanations, you told me everything in detail. The price was 35,000 tenge, I think it's fair.
Kia Sportage 2018, had problems with the automatic transmission — the gear wouldn't engage. Another service said the gearbox needed to be replaced. But here the guys dug around and found a chafed wire harness under the floor. They fixed the wiring and replaced the corrugated tube. Result: the gearbox works, I paid only 42,000 tenge. Very satisfied, saved a lot of money. I recommend!
BMW 520, the brake lights didn't work. I thought it was the bulbs, but it turned out the wiring in the rear light had rotted from corrosion. The guys replaced a section of wire and the connector, did everything quickly, in one day. The price was 22,000 tenge. You can immediately see they work carefully, all wires are in cambric sleeves, nothing is loose. I'll come back if needed.
Dear CARGID! My Lada Vesta stopped running — it would stall daily. Your technicians came, inspected it, and found a missing wire in the system. They also did an additional check and repaired everything. The cost was 18,000 tenge, and it took one day. Now my car runs great. Thank you!
Mercedes E220 CDI 2015, the alarm and parking sensors were malfunctioning. It turned out moisture got into the wire harness under the rear bumper. The guys disassembled it, dried it, replaced the connectors and treated everything with a protective compound. They worked for two days, the price was 50,000 tenge. A bit expensive, but now everything is perfect. The car is expensive, so I only trust such masters.
I want to thank the technicians for saving my Kia Rio. There was a broken wire in the door, which is why the central lock didn't work. Their diagnostics are fast, they explained everything, showed the old wire. They did it in one day, the cost was 16,000 tenge. Now everything locks properly. A pleasant impression: no pushing of unnecessary services.
I have a Skoda Octavia, the ABS sensor signal would periodically disappear. At CARGID they quickly found the problem — a break in the wire harness near the front wheel. They replaced the wire, insulated it, checked everything. I paid 20,000 tenge, which is very budget-friendly. Plus they gave a 12-month warranty on the work. It's a pleasure to deal with professionals.
The breakdown was unusual: on a Toyota Land Cruiser the windshield wipers stopped working. It turned out the wire harness in the hood had chafed. The technicians found it in 20 minutes, replaced the wires, installed a new corrugated tube. Fast and quality, done in 1 day, the price was 30,000 tenge. The car is like new now, I recommend this service to all my friends.
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.