Properly adjusted headlights are the key to your safety and comfort. We'll set the tilt angle and light direction according to the manufacturer's regulations, so as not to blind oncoming drivers and to illuminate the road well. We'll check and adjust low beam, high beam, and fog lights. Precise tuning in 30 minutes with a guaranteed result.
Headlight adjustment with manual leveler (sliders)
1 hour
12 mo
from 3,000 ₸
Headlight adjustment with electronic leveler
1–2 hours
12 mo
from 5,000 ₸
Headlight adjustment on vehicles with xenon lamps
1.5 hours
12 mo
from 6,000 ₸
Headlight adjustment on vehicles with LED headlights
1–2 hours
12 mo
from 7,000 ₸
Headlight adjustment for vehicles with air suspension
up to 2 hours
12 mo
from 8,000 ₸
Headlight adjustment after replacing lamps or optics
1–2 hours
12 mo
from 4,000 ₸
Headlight adjustment after an accident (body geometry)
2–3 hours
12 mo
from 9,000 ₸
Urgent headlight adjustment (same day)
1–2 hours
12 mo
from 5,000 ₸
Mobile headlight adjustment (around the city)
2–3 hours
12 mo
from 7,000 ₸
Headlight adjustment for SUVs and pickups (high ground clearance)
1.5–2 hours
12 mo
from 6,500 ₸
Headlight adjustment for minivans and commercial vehicles
2–3 hours
12 mo
from 8,500 ₸
Headlight tilt angle adjustment (leveler)
1 hour
12 mo
from 3,000 ₸
Fog light adjustment (if equipped)
1 hour
12 mo
from 2,500 ₸
Headlight testing and adjustment on a stand (optical method)
1–1.5 hours
12 mo
from 5,500 ₸
The exact cost depends on the make/model of the car, type of optics (lenses, xenon, LED) and the current condition of the mounts. The price includes labor only, excluding the cost of parts (if needed). Warranty periods — see the page «Warranty»
06
Why choose headlight adjustment at CARGID
Warranty.
Every promise — backed by a number or a document: work order, photos, removed parts.
12MO
warranty on labor — the term is stated in the work order.
Test bench verification
12-month warranty
Fast, in 30 minutes
01
We adjust using a device
We check the light output of each headlight on an optical stand, not «by eye». This way you can see where the beam actually hits, and the tilt is set according to standards.
02
Without removing the glass
We adjust xenon and LED through the standard screws, without disassembling the optics. The headlight seal is not broken, and condensation will not appear inside.
03
We check at 3 meters
After adjustment, we measure at a control distance and along the light-dark cutoff. We make sure we don't blind oncoming traffic and the roadside is visible.
04
After replacing lamps in 20 minutes
If a lamp or headlight was replaced, the position is disturbed. We re-set both sides so that the beams match in height and tilt.
07
How we adjust headlights: 6 steps
Steps.
From request to finished car — transparent and without surprises.
01
Vehicle acceptance
You leave a request on the website or by phone, we find a convenient time and book you in. At the service station we record the condition of the body and optics, and agree on the scope of work.
request on WhatsApp
02
Inspection and measurement
We take readings of the standard corrector, check tire pressure and the condition of the lamps.
inspection and diagnostics
03
Preparation for work
We place the car on a level surface, de-energize the optics and remove the protective covers.
estimate before work starts
04
Adjustment using instruments
Using an optical stand, we set the tilt angle and direction of the light beam.
work to factory procedure
05
Corrector check
We make sure that the electric corrector works in all modes and does not jam.
result check
06
Final diagnostics
We check the light-dark cutoff on the stand, and if necessary, adjust again. We show the results on the stand, issue a warranty for the work and hand over the keys.
Car service in Almaty. We reply on WhatsApp and by phone.
2 000 ₸Diagnostics and checking headlight aiming…
10 · Useful
Headlight Adjustment in Almaty on an Optical Bench by CARGID
Author: Роман Вернерgeneral car repair technician, 13 years of experience
Published Updated
CARGID in Almaty adjusts headlights on an optical bench, not "by eye": we set the tilt angle to spec, align both headlights as a pair and check the result at a control distance. We adjust xenon and LED through the stock screws without opening up the optics. The work is covered by a 12-month warranty, and we record the turnaround time in the work order.
How to Tell Your Headlights Are Off and It's Time for an Adjustment
A misaligned setup shows in how the light behaves on the road, not in how the optics look. Here are the symptoms that tell a driver it's time for the bench.
Signs of a Misaligned Setup
Oncoming drivers flash their high beams: they signal at you because your low beams hit their eyes higher than they should.
Uneven light cutoff: the light-dark cutoff runs in a step or a wave instead of a straight line.
One beam higher than the other: left and right sit at different heights, and the shoulder on the right drops into darkness.
The road is harder to see than usual: the light points down at the nose or up into the sky, and you have to squint.
Spots and gaps: instead of an even pool of light ahead, you get dark zones and bright patches at the edges.
The optics were removed: when a bulb is changed or mounts are repaired, the adjustment screws shift from their previous position.
Why the Setup Drifts and How Often to Check It
In our experience, alignment is most often thrown off by a bulb change, suspension repair, a sagging body and impacts — after each of these, the optics should be checked. The adjustment screws hold the reflector in one position, but when the unit is removed, the lens is changed or the struts are taken apart, their position shifts by a few degrees. Sagging springs and worn bushings change the tilt of the whole body, and with it the direction of the beam. Even a new bulb of the same base seats in the socket differently than the old one, and the light cutoff shifts. If you're unsure the beam is sitting straight, headlight adjustment in Almaty on the bench will show the deviation more accurately than a visual check. We check on the bench with an instrument, not against a wall. It makes sense to check every six months and always after any work on the front of the car. Even if the unit looks like it's in place, after a bulb change the beam sits differently — you need to align them as a pair, not just the side where the bulb was changed.
How Headlight Adjustment on the Bench Works
The difference between setting it "by eye" and with an instrument is that the bench shows the real direction of the beam. Here's what the check involves and why the result doesn't hold up without the instrument.
How an Optical Instrument Check Differs from Setting It by Eye
In our shop the setup is done with an instrument: we check the light output of each headlight on an optical bench, so you can see where the beam actually points, not roughly. The instrument reads the light-dark cutoff and the tilt angle to spec — the deviation is measured in degrees, not "higher or lower." In our experience, repeat visits are most often tied to setting it against a wall: the car sits unevenly, and the technician aims the optics relative to the surface, not the road. The bench works from its own optical axis, not from how the car is parked. The wall method doesn't account for body tilt and tire pressure — the instrument sets the required angle to spec, and the result doesn't depend on how the car sits on the lot.
What the Pre-Adjustment Check Includes
Tire pressure: we bring it to the spec on the door pillar sticker, otherwise the body is tilted and the beam pulls to one side.
Bulb condition: we check that both burn with even light and match in color temperature, otherwise the color mismatch will remain after the setup.
Stock leveling: we run the manual or electronic adjuster through all positions and make sure it actually moves the beam.
Optics condition: we inspect the lens and reflector for cracks, clouding and signs of condensation inside.
Setup and control measurement: we set the angle with the instrument and recheck the light-dark cutoff at a control distance.
Test drive before handover: we check the light on the road so oncoming drivers aren't blinded and the shoulder is visible.
Adjustment by Headlight Type and Vehicle
Different headlights and different cars are set up differently. We put the scenarios in a table and cover two common fears — xenon and LED — plus the high stance of SUVs and commercial vehicles.
Table of Adjustment Scenarios by Headlight Type and Vehicle
Setup scenarios by headlight type and body
Headlight or vehicle type
How we set the tilt
What we check
Manual leveling (slider)
stock screws and slider
leveler travel, headlight pairing
Electronic leveling
adjustment bolts, leveler position
electric leveler operation
Xenon
stock bolts without removal
auto leveling, washer
LED headlights
stock bolts without opening up
sealing, light cutoff
Air suspension
adjustment in several modes
body height sensors
SUVs and pickups
setup accounting for the lift
so oncoming drivers aren't blinded
Minibuses and commercial vehicles
setup to high-stance specs
pairing and light cutoff
Xenon and LED Without Removing the Headlight
We adjust xenon and LED modules through the stock bolts without opening up the optics — the housing seal isn't broken, and no condensation will form inside. Headlight adjustment on xenon and LED is done without removing or opening up the lens, so the sealant and reflectors stay untouched. On gas-discharge modules we separately check the auto leveling and the washer: without them the tilt doesn't stay in spec, and the beam goes above the light-dark cutoff. On LED optics we check whether the light cutoff has shifted after a bulb or ballast replacement, and only then adjust the mounts. Removing and opening up the lens for the setup isn't needed — it's an extra risk for the sealant and the inner reflectors. If the xenon beam points into the sky, it's more often the auto leveling or the sensor mounting at fault, not the bulb itself — so we check those before concluding "the unit needs replacing." This approach saves the owner money on unnecessary parts.
SUVs, Pickups and Commercial Vehicles
On lifted SUVs and commercial vehicles, the optics dazzle oncoming drivers because of the higher ride height — we set the tilt to the standards for that class. On pickups and minivans the beam sits higher than on passenger cars from the start, so a standard setting here throws light straight into the eyes of oncoming drivers. We also check left-right matching separately: both sides must produce the same cutoff line, otherwise you get a visible color mismatch on the road. A lift changes the geometry relative to the road, so a "stock" setting won't work here — we calculate the angle from the actual body height and check it at a reference distance. For minivans and commercial vehicles this matters especially: a loaded vehicle sags, and without rechecking under load the light drifts upward.
When Adjustment Won't Help and What to Do After an Accident
Sometimes poor light isn't about the setting but about the condition of the headlight itself. We tell you honestly when adjustment won't fix it, and we cover the post-accident case separately.
When Adjustment Won't Give Results
Cloudy lens: hazy plastic scatters the beam, and no screws will bring back a sharp cutoff line — the optics need restoring or replacing.
Cracks and chips: light escapes through damaged glass and moisture gets inside — the housing needs repair first.
Condensation inside: droplets on the lens and reflector distort the beam and also signal a broken headlight seal.
Burnt reflector: the coated layer fades over time, and the headlight shines weaker even at the correct angles.
Non-standard bulbs: an overly powerful bulb in unsuitable optics dazzles oncoming drivers, and adjustment won't save it.
Cracked mount: a broken bracket won't hold the housing, and the set angle drifts within a few kilometers — we replace the mount first.
Adjustment After an Accident and Body Repair
After an accident and a bumper replacement, the headlights are almost always off because the body geometry changes — we redo the setting taking the mount fit into account. Even a few-millimeter shift of a bracket sends the beam off to the side or up, and at a reference distance it's immediately visible at the cutoff line. We check the headlight position against the body gaps, verify the mounts themselves, and only then set the tilt with the equipment. If the body repair was done at our shop, the adjustment is the logical final step, and the body work carries a 24-month warranty. In my view, this isn't the stage to cut corners on: misaligned light after a crash is a common cause of dazzling oncoming drivers, and a recheck on the stand takes just a few minutes.
Timing, Booking and Work Warranty
Clients want to know how long the adjustment takes, whether they need to book ahead, and what happens if they're not happy with the result. Here's how our shop handles it, step by step.
How Long It Takes and How to Book
Headlight adjustment doesn't take long, and with a booking we take you without waiting — we're open daily from 09:00 to 20:00. Your car is met by the service advisor, who opens the work order and sees it through to handover: you know right away who's responsible for your vehicle. The specialist sets the beam on the optical stand while you watch, so you drive off the same day with verified light instead of leaving the car overnight. You can combine this procedure with a 3D wheel alignment in one visit — that saves a second trip to the shop. Book ahead for the morning or before 18:00: evening hours at Almaty auto shops are busier, and the wait stretches out.
Warranty and How We Work
Warranty period: we give 12 months on headlight adjustment and record the term and conditions in the work order and the handover report.
Warranty diagnostics: if the light goes off again after the work, we recheck it on the optical equipment free of charge.
Estimate up front: diagnostics and a written estimate first, and we start work only after the client agrees — the amount doesn't change along the way.
Photo report: we capture the key stages in photos so you can see what was adjusted and how.
Test drive before handover: the specialist checks the light while driving and shows you the cutoff line at a reference distance.
What affects headlight aiming
A quick summary of the topic: what really affects the result of a headlight setting and when it should be repeated without waiting for obvious symptoms.
Misaligned setting: an uneven cutoff line and oncoming drivers flashing their lights are the first signal to check the beam position.
Equipment instead of the eye: the stand shows the real direction of the light, and hand-tweaking against a wall doesn't give that precision.
Xenon and LED: set through the factory screws without opening the headlight, so the optics seal stays intact.
Cloudy lens and condensation: fix the cause first, then set the tilt — otherwise it all drifts again.
After an accident and a bumper replacement: the body geometry changes, so the procedure is redone using reference points.
Worth checking after a bulb replacement, suspension repair and any accident: the beam drifts unnoticed and dazzles oncoming drivers.
11
Frequently asked questions about headlight adjustment in Almaty
Questions.
Price, timeframes, warranty, payment — 10 questions asked most often.
10
Didn't find an answer?
Message us on WhatsApp — a service advisor will reply within 5 minutes.
The cost of headlight adjustment at CARGID is 5,000 tenge. This is the base price for adjusting low and high beams on a standard car. If you have projector headlights, xenon, or bi-xenon, the price may be slightly higher—7,000 tenge—as the process requires more precise tuning. We give the final cost after inspecting the car, but it is fixed in advance and does not change during the work.
On average, the procedure takes about 30–40 minutes. If the headlights require additional cleaning or there is minor damage to the mounts, the time may increase to an hour. We always try to complete the work quickly, but without compromising quality. The exact time depends on the condition of your car and the type of headlights, so it's better to make an appointment in advance so we can allocate a time slot for you.
Yes, we provide a warranty for all types of work, including headlight adjustment. The warranty is valid for 12 months or 10,000 km, whichever comes first. If within this period you notice that the headlights have become misaligned (for example, after hitting a pothole or replacing lamps), we will perform a repeat adjustment free of charge. To do this, you just need to contact our service with the payment receipt.
An appointment is desirable but not mandatory. If you come without an appointment, we will try to serve you within 30–60 minutes if there are available technicians. To guarantee a convenient time, especially on weekends, we recommend calling us and making an appointment. You can book by phone or through our website—it will take no more than a couple of minutes.
No, you don't need to bring anything except the car itself. Headlight adjustment does not require special spare parts or consumables—only professional equipment and the master's experience. Everything necessary is available at our auto service. If during the process it turns out that replacement of mounts or other parts is needed, we will inform you and offer solutions, but that will be a separate service.
If after adjustment you notice that the headlights are set incorrectly, come back to us—we will check and fix the problem free of charge if it is related to our work. However, keep in mind that poor light can be caused by other reasons: worn optics, cracks on the headlight glass, incorrectly installed lamps. In this case, we will perform diagnostics and offer a solution. We are interested in customer satisfaction, so we always meet you halfway.
Simple adjustment is setting the headlights according to the standard method: we set the vertical and horizontal angle of the light beam relative to the road. It is suitable for most cars with halogen lamps. Complex adjustment is required for headlights with xenon, bi-xenon, or projectors. Here it is necessary to precisely set the light cutoff, consider the automatic leveling system and the specifics of the optics, so it takes more time and requires special equipment. A separate price is provided for complex adjustment—7,000 tenge.
After adjustment, try to avoid strong impacts on the front of the car—for example, when parking near curbs, do not hit the headlights. Regularly wash the headlights from dirt and dust, as contaminated glass scatters light. If you change lamps, be sure to check their type and power—they must match the car's specification. And, of course, periodically visit the service for preventive checking of the adjustment—this ensures road safety.
Payment for headlight adjustment is accepted in cash, by bank card, and by transfer. The cost depends on the headlight design: for regular halogen, basic adjustment is sufficient; for projector and adaptive headlights, more time is required for tuning. The master gives the exact amount before starting work.
It is recommended to check headlight adjustment at least once a year, as well as after any work involving removal of headlights or replacement of lamps. This is especially important before long trips and after accidents or hitting serious obstacles. If you notice that the headlights have started to poorly illuminate the road, and oncoming drivers flash their high beams at you—this is a clear sign that the adjustment is off and you need to visit the service.
12
What drivers say about our headlight adjustment
Reviews.
We collect ratings on the website and on maps — we hide nothing.
4.8
872 reviews on the website 1 900+ ratings in total
Sergey
Toyota Camry
I came in a 2018 Toyota Camry. At some point the light started poorly illuminating the shoulder; at night it was impossible to drive. The guys took a look and said the headlights were misaligned after a pothole. They adjusted them in 20 minutes and showed the result on a stand. The light is perfectly even, now I can see everything. The price is 5000 tenge, which is quite low. Excellent service, I recommend.
Aigul
I had wanted to contact the service for a long time; my child's car had poor lighting. They didn't make us wait in line and checked it quickly. They adjusted the headlights, and now the light hits the road precisely. We paid 4500 tenge, the price is reasonable. While we waited after handing over the car, they gave us hot tea—now that's what service means!
Dmitry V.
Opel Astra
The problem was with a 2015 Opel Astra. After replacing the front struts, the headlights stopped shining where they should. I made an appointment at CARGID; the master checked and said that due to the change in body tilt, adjustment was needed. They did it in 30 minutes and showed on the stand that the beam was within norm. I paid 4000 tenge, all fair. Now I can see both road markings and signs.
Erlan
Mitsubishi Lancer 2012; after I replaced the lamps with LED, it started blinding oncoming drivers. I came here, the guys quickly figured out that the issue wasn't the lamps but the misaligned headlights. They checked the pressure, loaded the car according to the instructions, and adjusted. Everything is perfect. I paid 5500 tenge, but now no one flashes their high beams at me. I recommend!
Marina
I asked my husband to figure out why my Kia Ceed poorly illuminates the road at night. It turned out the right headlight was shining into the woods 🙂 The specialists at CARGID adjusted everything, put it on the stand, and showed how it should be. They did it quickly, with a smile. 5000 tenge — reasonable. Now even on unlit highways I drive calmly.
Kuanysh
We were tired of the headlights shining somewhere up, constantly flashing oncoming drivers. At CARGID they looked and found the leveling sensor was out of order. They set the sensor, adjusted the headlights, and reset the error. They did it quickly and cheaply (6500 tenge). Now all lighting is normal. Thanks to the guys!
Alexander
Prado
My Toyota Prado stopped shining properly after installing a bumper. The service said a stand was needed. I came here. While waiting, they asked to show the process—the master explained how headlights are adjusted. They did it considering the load; now the light is as it should be, both high and low beams. It cost 7000 tenge, but it's safe.
Irina
My daughter has a VAZ 2114, the headlights were shining unevenly. We thought we'd have to replace the optics, but it turned out just adjustment was needed. We made an appointment at CARGID, they did it in 40 minutes, and charged only 3500 tenge. My daughter is happy and drives calmly in the evening. Thank you for the conscientious work!
Talgat
CX-5
After a long trip on the highway, I noticed the light became weak. It turned out the headlight lost adjustment from vibration. At the service they set the profile for my Mazda CX-5 and checked the leveling sensor. They did it in 30 minutes and showed before and after on the stand. It was 6000 tenge, but now it shines like new. I recommend!