Over time, the windshield gets covered with micro-scratches from wipers, grains of sand, and road chemicals. This worsens visibility and makes driving dangerous. Windshield polishing removes up to 90% of defects and restores clarity. Don't replace the glass — trust hand polishing from CARGID!
We will determine the exact cost after diagnostics. Below are the base rates.
Service
Duration
Warranty
Price
Windshield polishing from scratches
1–2 hours
12 mo
from 8,000 ₸
Removal of small chips
30 minutes
12 mo
from 3,000 ₸
Deep scratch polishing
2–3 hours
12 mo
from 12,000 ₸
Polishing after wipers
1–1.5 hours
12 mo
from 7,000 ₸
Side window polishing
1–2 hours
12 mo
from 9,000 ₸
Rear window polishing
1–1.5 hours
12 mo
from 8,000 ₸
Headlight polishing
1 hour
12 mo
from 5,000 ₸
Deep glass polishing
2–3 hours
12 mo
from 15,000 ₸
Mirror polishing
30 minutes
12 mo
from 2,500 ₸
Tinted glass polishing
1–2 hours
12 mo
from 10,000 ₸
Polishing of glass with protective coating
2–3 hours
12 mo
from 20,000 ₸
Comprehensive polishing of all glass
3–4 hours
12 mo
from 25,000 ₸
Chip polishing with repair
1–2 hours
12 mo
from 6,000 ₸
Removal of brush scratches
1 hour
12 mo
from 5,000 ₸
Crack polishing (diagnostics)
30 minutes
12 mo
free
The price depends on the depth of defects, the car make, and the need for preliminary diagnostics. The exact cost will be told by the technician after inspection. Warranty periods — see the page «Warranty»
06
Advantages of windshield polishing at CARGID
Warranty.
Every promise — backed by a number or a document: work order, photos, removed parts.
12MO
warranty on labor — the term is stated in the work order.
Protective coating
Driving safety
Guaranteed results
01
We don't remove deeper than 40 microns
We work within the tolerance of 20–40 microns to avoid distorting the glass geometry. We measure thickness before and after polishing.
02
We polish at 40–60°C
We maintain this paste temperature: overheating warps the glass, a lower temperature means the scratch doesn't smooth out.
03
Window up to 1 hour
We polish tinted and side glass for a maximum of one hour per session to avoid overheating the film.
04
12-month warranty
We check the polishing under a lamp and angle gauge: if the scratch returns, we redo it for free.
07
What we do to the surface from diagnosis to finish
Steps.
Step by step: from request to finished glass.
01
Inspection and Diagnostics
You leave a request or call, we find a convenient time and schedule the polishing. The master inspects the glass under light, assesses the depth of scratches and chips.
request on WhatsApp
02
Washing and Cleaning
We clean the glass from dirt and dust, degrease the work area.
inspection and diagnostics
03
Abrasive Sanding
We select an abrasive paste and sand the damaged areas.
estimate before work starts
04
Polishing with Special Products
We polish the glass using special pastes and a polishing machine.
work to factory procedure
05
Quality Control
We check the result, make sure the defects are removed.
result check
06
Protective Coating
We apply a protective coating so the glass stays clean longer. You accept the work, we give care recommendations and a warranty.
Car service in Almaty. We reply on WhatsApp and by phone.
8 000 ₸Windshield polishing from scratches
10 · Useful
Windshield polishing in Almaty by CARGID with a warranty
Author: Аружан А.detailing specialist (mobile), 11 years of experience
Published Updated
CARGID performs windshield polishing in Almaty without removing the glass from the car: we first measure the thickness, work within a removal tolerance of 20–40 μm and never deeper than 40 μm. We remove wiper scratches and deep scuffs, apply a protective coating, and record a 12-month warranty in the work order.
When windshield polishing helps and when replacement is needed
Polishing is not a universal fix for every kind of damage. Let's draw the line right away: some defects can be completely removed, while for other damage we recommend repair or installing a new windshield.
Which defects polishing removes
Windshield treatment in Almaty removes defects that are no deeper than the working layer — surface scratches, wiper scuffs, fine "spiderweb" marks, and a dull trace in the wiper sweep area. Abrasive paste removes microns of the top layer and levels the surface, so optical clarity returns without installing a new part. The "spiderweb" from stones is a network of thin grooves left by sand grains caught under the wiper blade; such marks disappear in one pass if they don't go deeper. The wiper parking area wears faster than the rest of the windshield: the blade sits there constantly and works with sand. The depth of a defect is checked with a fingernail and by backlighting under a lamp: if a scratch "catches," it may go deeper than the working layer, and then the procedure will only give a partial result.
When polishing won't help and the glass needs to be replaced
If there is a chip or crack in the glass, we do not perform this procedure and recommend repair or replacement — removing the layer in the damaged area is dangerous. A chip is already a compromised glass structure, and treatment does not restore it but only masks the edge; vibration and temperature changes will make the crack continue to grow. The service advisor inspects the windshield when the car is checked in and immediately says which path will give a result — the client doesn't waste time on a procedure that won't help. We provide a 12-month warranty on windshield replacement, and the timeframe and conditions are recorded in the work order and the completion certificate at pickup. In our practice, it happens that an owner comes in for polishing but leaves with an appointment for replacement — that's more honest than taking on a job that won't solve the problem.
Wiper scratches and typical windshield defects
We explain where the streaks in the wiper area come from and why local glass wears faster than the car's appearance suggests — and what polishing does about it.
Why wipers scratch the glass
Blades leave marks when sand and dust remain under the rubber: in Almaty, with dust storms and road chemicals, the abrasive works like sandpaper in the wiper sweep area. The wiper parking area accumulates fine particles more than the rest of the surface — on the first swipe, a grain is pressed against the glass and drags along the arc. The chemicals spread on roads in winter soften the rubber, it loses elasticity and stops sweeping sand away, instead pressing it in. A worn blade with a trapped grain leaves a groove in one cycle — that's why defects appear within a season, not over years. It's worth wiping the wiper rubber at every fill-up and replacing it before the first track appears: a new blade costs less than subsequent polishing.
How to remove wiper scratches by polishing
We remove wiper scratches by abrasive sanding and finishing treatment in the wiper sweep area, keeping the removal depth within a tolerance of 20–40 μm. First, the technician assesses the defect: surface marks from the rubber are removed with abrasive paste in one pass, while deep grooves require a gradual transition from coarse to fine grit. The finishing paste removes dullness after sanding and restores clarity. We measure the glass thickness before and after — this shows that the geometry remains within normal limits. Only surface tracks disappear completely; if a groove is deeper than the working layer, after treatment it will become less noticeable but won't disappear — we honestly warn about this before starting work. In our practice, removing windshield scratches most often ends at the sanding stage — not every defect makes it to the finish.
How we avoid damaging the glass during polishing
The main fear before treatment is that the glass will become thinner, lose strength, or show uneven color. We keep both risks under control with two parameters: removal tolerance and paste temperature.
Removal tolerance and glass thickness measurement
We work within a tolerance of 20–40 μm and never remove more than 40 μm, and we measure glass thickness before and after treatment. We measure with a micrometer at several points in the treatment area — this shows how much material was actually removed and whether we've approached the limit. With such removal, the glass geometry remains normal, and the optical axis does not shift. This measurement is the only way to prove that the geometry hasn't been distorted: if removal has reached the upper limit, further work is pointless and dangerous, even when a scratch is still visible. On models with thin windshields — for example, after replacement with an aftermarket part — we start with a control measurement and, if necessary, reduce the depth to the lower end of the range. The client sees the numbers before and after in the work order, not just words.
Paste temperature and why uneven color doesn't appear
We keep the paste in the 40–60 °C range: overheating warps the glass, while insufficient heating doesn't close the scratch, and we check the result under a lamp and with an angle gauge. We measure the temperature with a pyrometer at the contact spot of the pad, not "by eye" — overheating can't be caught by ear or by the color of the paste. Uneven color appears when only the defect spot is treated: the area refracts light differently, and the outline is visible in backlight. We work the area with a smooth transition to neighboring zones — the treatment boundary is invisible, and there are no distortions. Dullness and streaks remain from unpolished paste or a dirty pad, so we change the pad on every car and finish with a soft paste. We check the result under a lamp from two angles — direct and oblique light reveal different defects.
How windshield polishing is done and how long it takes
Below is the sequence of stages and timeframes by type of glass, so you can understand how long the car stays in the shop and whether the part needs to be removed from the vehicle.
Stages and treatment timeframes
We polish windshields without removing them from the car: abrasive sanding, treatment with special products, inspection under a lamp and with an angle gauge, and a protective coating — by appointment, no waiting in line. First, the service advisor inspects the surface and records the defects in the work order, then a paste at the right temperature goes under the pad, and the zones are worked step by step from the edge to the center. At the finish, the surface is checked under a lamp from different angles and a hydrophobic coating is applied. The glass doesn't need to be removed because the work is done on the outer layer, but the car still stays in the shop for the duration of the procedure: first diagnostics and a written estimate, and we start the work only after the client agrees. Come at the start of the shift at 09:00 — then you'll pick up the car the same day, and before handover the technician will take it on a test drive and show you the result under angled light.
Types of work and what to look out for
glass treatment options and what makes each one different
Type of work
What we remove
Special feature
Warranty period
Windshield
Scratches, wiper marks
Thickness measurement, 20–40 µm removed
12 months
Side and tinted
Scuffs, dullness
Up to 1 hour per installation
12 months
Rear
Scuffs, brush marks
We work around the heating elements
12 months
Mirrors
Small scratches, cloudiness
Delicate part, careful removal
12 months
With protective coating
Finish after polishing
Hydrophobic layer over the treated surface
12 months
Warranty, result check and care after polishing
We put the warranty period and terms in the paperwork at handover, we check the result together with you on a test drive, and below we explain how to make the treatment effect last longer in city conditions.
What the 12-month warranty covers
We give a 12-month warranty on glass polishing, and we record the period and terms in the work order and the completion certificate at handover, and diagnostics for a warranty case are free. The service advisor handles the work order from intake to handover, so a warranty claim pulls up the same service history as when the car was dropped off. Before handover we take the car on a test drive and show the glass against the light under a lamp — you check the wiper zone together with us. The warranty covers the work performed and the parts installed, but not accidents after the repair, third-party interference or natural wear — this is written in the documents so there are no misunderstandings. If a streak appears in the wiper zone a few months later, come in for a free diagnostic: based on the results we'll decide whether it's a warranty case or a new cause.
Caring for the glass after polishing
Washing: no stiff sponges or scrapers, otherwise you'll get new scratches on the fresh layer.
Wipers: wipe the rubber and replace them at the first streaks, before they cut grooves.
Hydrophobic coating: renew it before the rainy season, then sand and road chemicals stick to the glass less.
In winter: don't scrape ice with metal and don't pour boiling water on cold glass.
Inspection: once a season, check the wiper sweep zone against the light under a lamp.
Key takeaways for windshield polishing
Here's the key stuff to keep in mind before windshield polishing — no technical details, just the takeaways that affect the result.
Limits of the method: the treatment smooths out surface scratches, scuffs and wiper marks, but not chips or cracks — those need the glass replaced or repaired.
Safe removal: the work relies on measuring thickness before and after and a limit of 20–40 µm; no more than 40 µm is removed so the geometry isn't thrown off.
Paste temperature: 40–60 °C and checking under a lamp are what separate an even result from uneven tone and dullness against the light.
Tinting and side windows: they're treated for a limited time per installation so the film doesn't overheat.
Making the effect last: a hydrophobic coating and fresh wipers noticeably slow down repeat wear and push back the next procedure.
11
Frequently asked questions about windshield polishing in Almaty
Questions.
Price, timeframes, warranty, payment — 10 questions asked most often.
10
Didn't find an answer?
Message us on WhatsApp — a service advisor will reply within 5 minutes.
The cost of windshield polishing at CARGID depends on the degree of damage and the treatment area. Basic polishing of minor scratches and scuffs from brushes costs from 15,000 to 25,000 tenge. If the glass has deep scratches or chips requiring multi-stage polishing, the price can reach 15,000 tenge. We provide the exact cost after inspection — it is free.
On average, polishing takes from 1 to 3 hours depending on the condition of the glass. Light damage — about 1–1.5 hours. If the glass is heavily scratched or has deep defects, it may take 2–3 hours, including preparation and polishing. We work without queues if you have booked in advance, and we try to stay within the agreed time.
Yes, we provide a warranty on the polishing result — 12 months. This means that if during this period the same damage that was removed appears on the treated area, we will re-polish for free. The warranty does not cover new scratches resulting from improper use or external influences.
An appointment is desirable but not mandatory. If you come without an appointment, we can accept you only if we have free time. On weekdays there are usually openings. To guarantee a slot at a convenient time, we recommend calling in advance and booking. It will take no more than 2 minutes.
Yes, you can bring your own materials if they are suitable for polishing automotive glass. However, we are not responsible for the result if unsuitable pastes or abrasives were used. Our service uses professional compounds that are selected for each case. This guarantees quality and safety for the glass.
If after polishing you find defects (smudges, scratches not fully removed), contact us immediately. During the warranty period, we will fix the shortcomings for free. Important: do not try to rub the glass yourself, this may damage the coating. Come in, we will look and fix the situation.
We offer two main options. Local polishing — treatment of one area, for example, the driver's zone. It is cheaper (from 10,000 tenge) and is suitable if defects are concentrated in one place. Comprehensive polishing — polishing of the entire glass. Recommended for multiple scratches over the entire area, costs from 20,000 tenge. Comprehensive polishing ensures uniform optics and better removal of damage.
After polishing, within 24 hours it is not recommended to wash the glass or use windshield wipers. After that, wash with regular glass cleaners without abrasives. Wiper blades should be in good condition to avoid scratching the surface. Also avoid prolonged sun immediately after the procedure: the glass should not overheat in the first 24 hours so that the polishing "sets".
Yes, we accept cash and bank cards (Visa, MasterCard). You can also pay via QR code through Kaspi or Kaspi transfer; for legal entities, payment by bank transfer with a receipt is possible. We do not offer installments, but the service is inexpensive, so most clients pay immediately after completion.
No, we polish the glass directly on the car. Removing the glass is not required — this speeds up the work and eliminates the risk of damaging the seals. However, if the glass has chips or cracks, polishing will not help — we can repair them or recommend replacement. In such cases, we do not perform polishing to avoid worsening the condition.
12
What clients say about our windshield polishing
Reviews.
We collect ratings on the website and on maps — we hide nothing.
4.8
872 reviews on the website 1 900+ ratings in total
Alexey
Kia Rio
Came in with wiper scratches on a Kia Rio. They did the polishing in one day, 20,000 tenge. It became perfectly clean, the wipers glide silently. Thanks to the technician!
Dmitry
After winter the glass became dull, nothing was visible. Booked polishing at CARGID. The technician looked at it, said it was minor. They did it in a couple of hours, 25,000 tenge. The result is excellent, the glass is transparent, like new.
Aigul
Toyota Camry
Had the windshield polished on a Toyota Camry. There were scratches from sand after a trip on the highway. They removed everything, the price was pleasing - 28,000 tenge. Now the road doesn't bother me.
Sergey
There were swirl marks after a poor-quality car wash. Polishing cost 22,000 tenge. They did it quickly, the glass is clean and transparent. I will recommend it to friends.
Maria
My husband scratched the glass by hitting a rough wall. Polishing took two days, cost 32,000 tenge. But now even small scratches are not visible. Thank you for your patience and quality.
Erlan
Tucson
They polished the glass well on a Hyundai Tucson. There was dullness after winter. It became clean and transparent. I paid 30,000 tenge. The work was done neatly.
Olga
I searched for a long time for a place to remove scratches on the glass. At CARGID they did an excellent job. The price is 25,000 tenge, the time is one day. I am satisfied with the result.
Irina
I got caught in a sandstorm, the glass was all scratched. Here they polished it, now it's like new. I paid 28,000 tenge. Thanks for the fast service.
Azamat
Excellent windshield polishing! There were scuffs from the brushes. They did it for 20,000 tenge, visibility improved significantly. I recommend it.