Authorexperience

STP soundproofing is a comprehensive solution for car comfort. We reduce noise and vibration, protect the body from corrosion, and improve acoustics. We use original STP materials: vibration insulation, sound insulation, anti-squeak. We select an individual scheme for each brand. 24-month warranty on all work.
STP materials: hood, doors, floor, wheel arches, ceiling, trunk.

We glue one layer of STP Accent+ on the hood. It dampens engine hum and protects the paint from heat.

We lay the trunk floor and wheel arches in two layers of STP Barrier. The hum from the rear of the cabin goes away.

On all four doors — two layers: STP Aero and Splen. The doors close with a deader sound, and road noise becomes quieter.

Composite sheets and wheel removal for treating the arches. Noise from tires and small stones is reduced.

We treat the front and rear floor: STP Barrier plus Accent. Road and exhaust hum becomes quieter.

We glue STP Aero and Splen on the headliner. Less noise from rain and less hum in the cabin.

We lay STP Aero on the parcel shelf and body pillars. It eliminates rattling and extra noise from the rear.

Choose the parameters — we'll show a price and time estimate. We'll confirm the exact quote after diagnostics and send the result to WhatsApp.
Labor. Parts and materials depend on make and availability, OEM or aftermarket.
Calculation details go into the message · reply in 5 minutes
High-quality sound insulation using STP materials: we reduce noise and vibration and make every trip more comfortable.
| Service | Duration | Warranty | Price |
|---|---|---|---|
| Vehicle inspection, noise diagnostics, consultation on material selection | 30–40 minutes | 24 mo | Free |
| Hood sound insulation (STP Akcent+ material), 1 layer | 1–2 hours | 24 mo | from 15,000 ₸ |
| Trunk sound insulation (floor and wheel arches, STP Barrier), 2 layers | 2–3 hours | 24 mo | from 25,000 ₸ |
| Door sound insulation (4 doors, STP Aero + Splen), 2 layers | 3–4 hours | 24 mo | from 45,000 ₸ |
| Front wheel arch sound insulation (composite, wheel removal) | 3–4 hours | 24 mo | from 35,000 ₸ |
| Cabin floor sound insulation (front and rear sections, STP Barrier + Akcent) | 4–6 hours | 24 mo | from 60,000 ₸ |
| Headliner sound insulation (STP Aero + Splen) | 3–4 hours | 24 mo | from 40,000 ₸ |
| Parcel shelf and pillar sound insulation (STP Aero) | 1–2 hours | 24 mo | from 12,000 ₸ |
| Full cabin sound insulation (floor, doors, headliner, wheel arches, trunk) | 2–3 days | 24 mo | from 180,000 ₸ |
| Firewall sound insulation (without engine removal, STP Barrier) | 3–5 hours | 24 mo | from 30,000 ₸ |
| Roof sound insulation (for vehicles with sunroof, STP Aero) | 2–3 hours | 24 mo | from 20,000 ₸ |
| Express sound insulation of one zone (door, wheel arch) on the day of request | 1–2 hours | 24 mo | from 10,000 ₸ |
| Mobile sound insulation (at the client's location, standard zone) | from 2 hours | 24 mo | from 25,000 ₸ |
| Removal and reinstallation of interior trim (complex vehicles) | 2–4 hours | 24 mo | from 8,000 ₸ |
| Liner and wheel well sound insulation (STP Aero, dirt protection) | 1–2 hours | 24 mo | from 10,000 ₸ |
| Spare wheel well sound insulation (STP Barrier + Akcent) | 1–2 hours | 24 mo | from 12,000 ₸ |
| Tunnel and driver's footwell sound insulation (STP Barrier) | 2–3 hours | 24 mo | from 18,000 ₸ |
| Rear wheel arch sound insulation from inside the cabin (without suspension removal) | 2–3 hours | 24 mo | from 22,000 ₸ |
The exact cost depends on the vehicle make/model and the selected STP materials. Travel within Almaty is free for orders from 50,000 ₸. Warranty periods — see the page «Warranty»
Every promise — backed by a number or a document: work order, photos, removed parts.
warranty on labor — the term is stated in the work order.
We carefully remove trim, seats, and clips with a fastener gun and removal tools. We put everything back without squeaks or broken clips.
Vibroplast, then sound absorber and mastic on top. One layer removes the thud, the others — the hum at speed, the difference is audible at 100 km/h.
We heat the vibroplast with a construction heat gun and roll it with a roller. In cold, the material doesn't stick, so it falls off after a month.
We cover peeling, bubbles, and detachment at the edges. If the layer comes off due to our fault, we re-glue it for free.
We explain step by step: from request to vehicle handover.

You submit a request on the website or by phone, and we find a convenient time. A technician inspects the vehicle, determines the scope of work, and gives an exact price.
request on WhatsApp
We carefully remove the seats, trim, headliner, and trunk for access to the body.
inspection and diagnosticsWe clean and degrease the metal so the materials adhere evenly and last long.
estimate before work starts
We roll out vibration damper, sound and heat insulation STP over all zones.
work to factory procedureWe return the interior elements to their places, check fasteners and gaps.
result check
We test the vehicle on the road: listen for any extraneous noises and squeaks. We hand over the car with a warranty on the work and give care tips.
warranty in the work orderWalk-ins welcome. By appointment — no queue.
Detailing team. 9–18 years of experience.
Author
Body polishing specialist

Interior deep cleaning specialist

Polishing specialist

Detailing specialist

Write to WhatsApp with the make, year and what's bothering you. We'll tell you the cause, a price estimate and pick a time for your visit.
available daily 09:00–20:00CARGID
Car service in Almaty. We reply on WhatsApp and by phone.

CARGID does STP soundproofing in Almaty for all body zones — from a single door to a full cabin package. We follow a three-layer scheme, heat the vibration damper with a heat gun to 60 °C and roll it with a roller, so the material doesn't peel off in the heat. The 24-month warranty is recorded in the work order.
We cover all body zones — from a single door to the full package. Below we explain what the full cabin treatment includes and what individual options are available.
Our full package covers the front and rear floor, four doors, ceiling, front wheel arches and trunk — all zones in one estimate. STP soundproofing in Almaty is assembled from different materials for each surface: Barrier with Accent goes on the floor and doors, Aero with Splen on the ceiling, and we cover the arches with a composite. We completely disassemble the interior: remove the trim, seats, and clips — using a trim tool and clip gun so everything goes back without squeaks or broken fasteners. A service advisor accepts the car and manages the work order until handover, and we take photos at key stages. It's more cost-effective to do the full package at once: we remove the trim and seats only once, and re-disassembling for a single zone is an extra risk for the clips.
| Zone | STP material | Layers |
|---|---|---|
| Hood | Accent+ | 1 |
| Doors (4 pcs.) | Aero + Splen | 2 |
| Cabin floor | Barrier + Accent | 2 |
| Trunk (floor and arches) | Barrier | 2 |
| Front wheel arches | composite | 1 |
| Ceiling | Aero + Splen | 2 |
| Firewall | Barrier | 1 |
We explain the difference between vibration damping and sound absorption, why the third layer of mastic is needed, and why different STP materials are used on different body zones.
Vibration damper reduces metal vibration and is applied first, the sound absorber absorbs airborne noise and goes second, and mastic covers the top and protects from moisture. The vibration damper is a bitumen-rubber sheet on foil: it converts panel vibrations into heat, so the door stops humming when you tap it. A porous layer like Splen or Accent+ catches the sound wave inside the cabin and prevents it from reflecting off the metal. The mastic on top seals the seams and keeps moisture away from the adhesive. This three-layer scheme works as a single system, not a set of separate sheets. STP car soundproofing is built exactly on this layer order; otherwise even expensive materials won't give the expected effect. If you put a porous material directly on bare metal, it doesn't work — without a vibration damper underneath, the panel keeps resonating and the effect is lost entirely.
We apply three layers to the floor and doors — vibration damper, sound absorber and mastic; one layer removes the thud, but the hum at 100 km/h is only gone after all three. On the floor we use Barrier as a vibration damper and Accent+ on top; on the doors, Aero with Splen, because thin trim doesn't like heavy sheets. CARGID uses the three-layer scheme specifically on these zones: they contribute most to road noise. The ceiling and rear shelf need only two layers of Aero and Splen — vibration there is weaker than on the floor, and extra weight on top only hurts. Before choosing the material, the technician taps the panel and listens to its resonant frequency — this determines the thickness of the vibration damper.
Peeling is almost always caused by cold installation and poorly prepared surface. We show how we heat the material, roll it with a roller, and why the coating holds up in summer heat.
We heat the vibration damper with a heat gun to 60 °C and roll it with a roller — when cold, the adhesive doesn't stick and peels off within a month. The technician moves the heat gun along the panel and immediately rolls each section with a roller from the center to the edges to squeeze out air from under the layer. This way the material lays flat without bubbles and doesn't stretch as it cools. Before applying, we degrease the metal: dust and oil film kill adhesion even on heated vibration damper, so preparation is as important as the heat gun. Without heating and rolling, the coating doesn't hold, so we never skip these steps. In our experience, returns for peeling are due to an unheated or unrolled layer, not a defective roll, so we heat and roll every panel, not selectively. We have a heat gun and roller at every bay, so this step doesn't drag out. Soundproofing with STP materials only holds with proper heating and rolling — we never skip these steps.
Properly heated and rolled vibration damper holds up in Almaty heat, while unheated material slides down vertical door panels in the first season. In summer, the body metal in the sun gets hotter than in the shop, and the temperature difference between the layer and the metal works against weak adhesion. On doors and pillars, the coating hangs vertically, so that's where poor rolling shows up first — the layer slides down and exposes the top edge. Adhesion margin is built in during installation: redoing it on finished trim costs more than heating it right the first time. According to our technicians' experience, Almaty summer tests the adhesive seam harder than winter frosts — and only properly rolled material withstands it. Car owners who come with peeling after other shops most often complain about doors and pillars.
Clients worry that disassembly will cause squeaks or broken clips. We show what tools we use to remove the trim and how we verify the result before handing over the car.
We remove the trim, seats and clips with trim tools and a clip gun, not by prying with a screwdriver — this way the fasteners stay intact and everything goes back without squeaks. On plastic panels we use clip removal tools with a wide blade: they distribute force over the area and don't leave dents. The clip gun seats the clips with even force, so the fastener clicks into place instead of being crushed. Where old fasteners have lost their elasticity, we install new ones — a broken clip is a common cause of rattles. We apply anti-squeak tape around the perimeter of panels so plastic doesn't rub against metal. In our experience, a common cause of strange noises after someone else's reassembly is dry and torn clips. Therefore, after installing the trim, we run our hand along the perimeter and check the fit of each panel.
Before handing the car over, we do a test drive and listen to the cabin at speed — that's how we check there are no squeaks, peeling, or odd noises after reassembly. We drive over rough pavement and a stretch with quick acceleration: at 100 km/h you can hear what's going on with the floor and doors, and on seams and speed bumps plastic rattles show up. We log every stage in a photo report — the photos show how the layers were laid and how the trim was put back together. If the client notices a squeak later, diagnosis for a warranty case is free: first we find the source, then we decide whether it's a warranty case or not. The soundproofing warranty is 24 months, and we write the term and conditions into the work order. In my view, the test drive saves both sides time: a questionable noise gets caught before handover, not a week later.
We break down exactly what the soundproofing warranty covers, which cases fall outside it, how we work with client-supplied materials, and how long booking and the work itself take.
The soundproofing warranty is 24 months; it covers the work performed and the materials installed, and the term and conditions are written into the work order and acceptance report. We do diagnosis for a warranty case free of charge: the technician inspects the area, checks it against the stage-by-stage photo report, and records the cause. If the vibration damping material came loose through our fault, we fix it under warranty, with the term and conditions written into the work order. The warranty covers the work performed and the materials installed, not a part the client brought in. It does not cover an accident after the repair, interference by third parties, normal wear of consumables, or a part brought in by the client — these are the boundaries it's better to know before booking, not afterward. In my view, an honestly spelled-out scope matters more than a big number: the client understands up front what the technician is responsible for and what he isn't.
We accept client-supplied STP materials: installation is covered by warranty, but the properties of the material you bring are on you; book in advance, we work daily 09:00–20:00 with no days off. With a booking, a service advisor takes in the car and manages the work order through to handover, so there's no need to wait in line. We inspect the batch before gluing: we check the production date, the integrity of the roll, and how the sheet behaves when heated with a heat gun. If the batch raises doubts, we warn you right away, before work starts, not at the end. The installation warranty still applies, but if the material you brought is what came loose, the warranty doesn't cover it. From our experience: old material sticks worse than fresh, and you can see it on the very first sheet.
We agree on the exact time to the hour after inspection, and we take on an urgent area the same day if there's a slot in the schedule. The full package includes the floor, doors, ceiling, wheel arches, and trunk, and each area needs its own time for disassembly and heating. We agree on the exact time after inspection. Urgent treatment of a single area — the doors or wheel arches — is realistic the same day, but only if there's an open slot in the schedule. The time depends on how complex the disassembly is: on cars with complex trim, taking things apart takes longer than the gluing itself. That's why we ask for the model when you book — the service advisor uses it to estimate the labor in advance. We agree on the exact time after inspection, not over the phone.
Here's the main thing to keep in mind before booking the treatment: what the result depends on, how long it takes, and what the warranty covers.
Price, timeframes, warranty, payment — 10 questions asked most often.
Message us on WhatsApp — a service advisor will reply within 5 minutes.
Ask a questionThe cost of STP soundproofing at our service depends on several factors: the make and model of the car, the scope of work (soundproofing of the floor, doors, roof, trunk, or a full package), the selected STP materials (e.g., vibration isolation STP Gold, Aero, Biplast, etc.), and the condition of the body. On average, soundproofing one door costs from 15,000 to 25,000 tenge, and full interior soundproofing (floor, doors, roof, trunk) — from 180,000 tenge depending on the car. We provide an exact price after inspecting the car and drawing up an estimate.
The timeline depends on the scope of work. Soundproofing one door takes about 2-3 hours. A full package (floor, doors, roof, trunk) is usually completed in 2-3 working days. The time may be affected by the complexity of disassembling the interior, additional requests (e.g., additional soundproofing of the wheel arches), and the service's workload. We provide exact timelines after diagnostics and agreement on the scope of work.
Yes, we provide a warranty for the work performed — 24 months. The warranty covers the quality of installation of STP materials: no peeling, no squeaks, proper adhesion. If defects related to our work occur during the warranty period, we fix them free of charge. The warranty does not cover mechanical damage caused by an accident or careless operation of the car.
Yes, we recommend booking in advance, as the service is in demand. You can call us or leave a request on the website — we will find a convenient time. If you book 2-3 days in advance, we guarantee that we will start work on the agreed day. If you need it urgently, call us — we may find a slot in the coming days.
Yes, you can bring your own STP materials. However, we are responsible only for the quality of installation and are not responsible for the properties of the materials. Before starting work, the technician will check the integrity of the material, its suitability for the surface type, and give recommendations. If the material is not suitable for the given car, we can offer our own materials at a similar price with a guaranteed result.
If you find defects after our work (squeaks, peeling, unglued areas), contact us immediately. During the warranty period, we will fix the defects free of charge. If the problem is not our fault (e.g., due to moisture or mechanical damage), we will offer a solution at a reasonable cost. It is important not to delay contacting us to prevent further peeling of the material.
Different STP materials perform different functions. Vibration isolation (e.g., STP Gold, Aero) — these are heavy bitumen or mastic sheets that damp body vibrations. Soundproofing (e.g., STP Biplast, Accent) — these are porous materials that absorb sound and prevent its spread. There are also combined materials like STP Aero Plus that combine both effects. Depending on the client's goals, we select the optimal set: to combat tire roar — vibration isolation of the wheel arches, for silence in the cabin — a combination of vibration and soundproofing.
Immediately after the work, it is not recommended to wet the interior for 24 hours so that the adhesive sets. During the first 2-3 days, try not to load the body (do not carry heavy loads) and avoid driving over large potholes. Care after soundproofing is not difficult: regular dry cleaning of the interior. Do not use aggressive chemical agents for washing the floor, as they may damage the material. If you find moisture (e.g., leaks), contact us — we will check the sealing.
Payment for STP soundproofing is made in a single payment after acceptance of the work. We accept cash, bank cards, and bank transfers. If the scope is large, we agree on the cost and payment procedure before starting work.
The full soundproofing package includes treatment of the floor, doors, roof, trunk, and engine compartment partition. We remove the trim, carpets, panels, and glue the surfaces with vibration isolation (usually 2 layers in critical areas) and soundproofing. This reduces the noise level in the cabin by 60-70% and improves acoustic comfort. If necessary, we additionally soundproof the wheel arches. The cost of the package is calculated individually after inspecting the car.
We collect ratings on the website and on maps — we hide nothing.
872 reviews on the website
1 900+ ratings in total
Had soundproofing done on a Kia Sportage. The cabin became noticeably quieter, the road hum from the wheels almost disappeared. They worked for two days, the price was 180 000 tenge, as promised. Very satisfied, thanks to the craftsmen!
Came on a friend's advice, had full soundproofing done on a Toyota Camry. The result exceeded expectations — the cabin became very quiet, the music sounds better. It cost 350 000, but it's worth it. I recommend!
Finally got the door soundproofing done on my Nissan. The thud when closing became pleasant, the noise from outside is less. The work took only a day, the price was 95 000 tenge. Excellent service, polite craftsmen.
I complained about the noise and heat from the ceiling in my Mazda 6. They did heat and sound insulation, now the cabin is comfortable even in the scorching sun, and you can't hear the rain. The price was 70 000, they worked quickly. The car was returned clean, everything neat.
Ordered trunk soundproofing on a Volkswagen Tiguan. The rattling went away, it became quieter in the back. They did it in 6 hours, I paid 55 000 tenge. Thanks for the promptness!
Had arch soundproofing done on a Honda CR-V. The tire hum disappeared, driving became more comfortable. The price was 120 000, the time was a day and a half. Pleasantly surprised by the attitude — they explained everything, showed the materials.
Full soundproofing on a Toyota RAV4. It was very noisy, especially on the highway. After the work it became noticeably quieter, the music started to sound different. The price was 350 000, but the result is pleasing. I recommend the service.
Tap the heart if the review helped.
Almaty. daily 09:00–20:00. By appointment — no queue.
Choose a platform — your review will be seen by everyone looking for a car service in Almaty. Mention the work order number in the text.